Denon AV Surround Receiver, AVR-1612 manual 95

GAudioH

Symptom	Cause/Solution	Page
Audio is not output.	• Check the connections for all devices.	C 3,
	• Check the speaker connections and configurations.	6, 7, 8, 9, 10
		C 6,
	• Check whether the audio device power is turned on.	59, 60
		–
	• Adjust the master volume.	19
	• Cancel the mute mode.	19
	• Select a suitable input source.	18
	• Select a suitable input mode.	69
	• Disconnect the headphones. No sound is output from the speakers	78
	or the PRE OUT connectors when headphones are connected.
No sound is	• Check if the surround speakers are connected to the SURROUND	–
produced from	terminals.
surround speaker.
No sound is	• Check if “Pre Assign” is set appropriately in order to output audio	59
produced from	from the surround back speakers.
surround back	• Set “Speaker Config.” – “S.Back” on the menu to something	59
speaker.	other than “None”.
	• Set “Surr.Parameter” – “S.Back” on the menu to something	53
	other than “OFF”.
	• Set the surround mode to something other than “STEREO” and	29
	“VIRTUAL”.
No sound is	• Set “Surr.Parameter” – “PLgz Height” on the menu to “ON”.	53
produced from front	• Check if “Pre Assign” is set appropriately in order to output audio	59
height speaker.	from the front height speakers.	60
	• Set “Speaker Config.” – “F.Height” on the menu to something
	other than “None”.
No sound is	• Check the subwoofer connections.	C 6,
produced from		36, 37
subwoofer.
	• Turn on the subwoofer’s power.	–
	• Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.	59
	• If “Front” and “Center” for “Speaker Config.” are set to “Large”,	59, 60
	and “Subwoofer Mode” is set to “LFE”, no sound may be output
	from the subwoofers, depending on the input signal or selected
	surround mode.
DTS sound is not	• Set “Decode Mode” on the menu to “Auto” or “DTS”.	69
output.
Dolby TrueHD, DTS-	• Make HDMI connections.	6
HD, Dolby Digital
Plus audio is not
output.

Symptom	Cause/Solution	Page
Dolby PLg mode or	• Check that “Speaker Config.” – “Center” or “Surround” is set	59
DTS NEO:6 mode	to other than “None”. If the speaker system is 2.0/2.1ch, this
cannot be selected.	surround mode cannot be selected.
	• When headphones are used, Dolby PLg or DTS NEO:6 cannot be	–
	selected.
Audyssey MultEQ®,	• Switch the surround mode to other than “DIRECT”.	32
Audyssey Dynamic	• When headphones are used, MultEQ®, Dynamic EQ® and	–
EQ® and Audyssey	Dynamic Volume® cannot be selected.
Dynamic Volume®
cannot be selected.
Dynamic EQ® and	• Make Audyssey® Auto Setup.	11, 40
Dynamic Volume®
cannot be selected.
RESTORER cannot	• Check that an analog signal or PCM signal (fs=44.1/48 kHz) is	56
be selected.	input. For playback of multichannel signals such as Dolby Digital
	or DTS surround, RESTORER cannot be used.
	• Switch the surround mode to other than “DIRECT”.	32
GRadioH
Symptom	Cause/Solution	Page
Reception fails, or	• Change the antenna orientation or position.	10
there is a lot of noise	• Separate the AM loop antenna from the unit.	10
or distortion.	• Use an FM outdoor antenna.	10
	• Separate the antenna from other connection cables.	10
GControl dock for iPodH
Symptom	Cause/Solution	Page
iPod cannot be	• Check the iPod connections.	9
played.	• Insert the AC adaptor of the iPod control dock into the power	–
	outlet.
	• Switch the input source to “DOCK”.	18

version Basic

version Advanced

Information

92