Denon AVR-2802/982 ENGLIS Preset memory Audio component, Preset memory Video component

ENGLIS

Preset memory (Audio component)

•DENON components can be operated by setting the preset memory for CDR or MD. Operation is not possible for some models, however.

In this case use the learning function (see page 32) to store the remote control signals.

•For instructions on clearing the presettings stored in the preset memory, see page 35.

1	Set the slide switch to “AUDIO”.
		AUDIO
		AVR/AVC			VIDEO
2	Set the slide switch to “CDR/MD.
		TAPE	CDR/MD
	CD					MULTI
		DVD				TV
		VDP		VCR

3	Holding in the POWER button, press the
	button for the components you want to
	set.

The LEARNED/TX LED flashes.

	START	LEARNED/TX	RC-903
SYSTEM CALL		POWER
SET	CALL	OFF	ON / SOURCE
DVD	VDP	TUNER	SHIFT
1	2	3
TV/DBS		PHONO
4	5	6
VCR-1	CD	CDR / TAPE	CHANNEL
7	8	9
VCR-2/V.AUX			TV/VCR
+10	0		A / B
VOLUME			DISC SKIP+
	DOLBY / DTS
SPEAKER	SURROUND	DIRECT
DSP SIMULATION	5CH / 6CH STEREO	STEREO
			MASTER VOL.
INPUT MODE	ANALOG	EXT.IN

3

3

Keep the POWER button pressed in	)
( when performing steps 3 and 4

1	AUDIO		TAPE	CDR/MD
			CD	MULTI	MUTING
	AVR/AVC	VIDEO	DVD	TV
			VDP	VCR
			SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER

Combinations of Personal System Codes

“CDR/MD”

DIRECTSTEREOEXT.IN

		(DIRECT)	(STEREO)	(EXT. IN)
ON / SOURCE	(POWER)	DENON CDR A	DENON CDR B	DENON MD

2

*

Preset codes set upon shipment from the factory.

Preset memory (Video component)

•DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not possible for some models, however. In this case use the learning function (see page 32) to store the remote control signals.

•For instructions on clearing the presettings stored in the preset memory, see page 35.

1	Set the slide switch to “VIDEO”.			4	Next, while holding the POWER button,
		AUDIO			press the button for the code in block B.
					(Refer to Table 1.) The operation is
					completed when the button is released and
		AVR/AVC	VIDEO
					the LEARNED/TX LED lights.

RC-903

	START	LEARNED/TX		3,4
SYSTEM CALL		POWER
SET	CALL	OFF	ON / SOURCE
DVD	VDP	TUNER	SHIFT

2	Set the slide switch to the component to				3
	be registered (DVD, VDP, VCR or TV).
	TAPE	CDR/MD
	CD	MULTI
	DVD	TV
	VDP	VCR		5
	Keep the POWER button pressed in		)		To continue registering other components,
					repeat steps 2 to 4.
	( when performing steps 3 and 4				1

3	Holding in the POWER button, press the
	button for the corresponding manufacturer
	in block A.	Flashes
	(Refer to Table 1.)

1	2	3
TV/DBS		PHONO
4	5	6
VCR-1	CD	CDR / TAPE	CHANNEL
7	8	9
VCR-2/V.AUX			TV/VCR
+10	0		A / B
VOLUME			DISC SKIP+
	DOLBY / DTS
SPEAKER	SURROUND	DIRECT
DSP SIMULATION	5CH / 6CH STEREO	STEREO
			MASTER VOL.
INPUT MODE	ANALOG	EXT.IN
AUDIO	TAPE	CDR/MD
	CD	MULTI	MUTING

AVR/AVC	VIDEO	DVD	TV
		VDP	VCR

	SYSTEM	SURROUND
TUNING	SETUP	PARAMETER
BAND	TITLE	MENU/GUIDE
		CH SELECT
MODE		ENTER
		SELECT
MEMORY	STATUS	ON SCREEN
	DISPLAY	RETURN
USE/LEARN T.TONE	MULTI	DVD
		SET UP

4

2

The LEARNED/TX LED flashes.

•This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown on Table 1.

29