Denon AVR-2802/982 operating instructions Learning function

MUTING

SURROUND PARAMETER

MENU/GUIDE

ON SCREEN

RETURN

DVD

SET UP

TV/VCR

A / B

DISC SKIP+

MASTER VOL.

RC-903

ENGLISH

Learning function

•If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-2802/982’s remote control to “learn” the codes from the component’s original remote control.

•The buttons that can be “learned” are the CD, TAPE and CDR/MD system buttons (see page 28) and

the DVD, VDP, VCR and TV system buttons (see page 31). (For the CD, CDR/MD, DVD, VDP and TV, the			START	LEARNED/TX
		SYSTEM CALL		POWER
		SET	CALL	OFF	ON / SOURCE
A block buttons can also be “learned”, and for the DVD and TV, the B block buttons can also be		DVD	VDP	TUNER	SHIFT
		1	2	3
“learned”.)
	A	TV/DBS		PHONO
		4	5	6
		VCR-1	CD	CDR / TAPE	CHANNEL

1	Press the USE/LEARN selector button with the tip of a pen		7	8	9
			VCR-2/V.AUX
	etc., to set the learn mode. Both the START and LEARNED/TX		+10	0
	indicators flash.	Flashes

4

This unit’s remote control unit

VOLUME

DOLBY / DTS

SPEAKER SURROUND DIRECT

DSP SIMULATION	5CH / 6CH STEREO	STEREO
INPUT MODE	ANALOG	EXT.IN

2	AUDIO		TAPE	CDR/MD
			CD	MULTI
	AVR/AVC	VIDEO	DVD	TV
			VDP	VCR

	SYSTEM
TUNING	SETUP
BAND	TITLE
	CH SELECT
MODE	ENTER
	SELECT

3

B

Set the program switch to the side to be learned.

2 Set to the AUDIO side for the CD, tape deck or CDR/MD position, to the VIDEO side for the DVD, VDP, VCR or TV position.

	MEMORY	STATUS
1,8		DISPLAY
	USE/LEARN T.TONE	MULTI

	AUDIO		5	Check that the START LED is lit, then press the button to be
	AVR/AVC	VIDEO		“learned” on the other remote control unit.
3	Set the program switch to the position to be learned.			Other remote
				control unit
	TAPE	CDR/MD
	CD	MULTI
	DVD	TV
	VDP	VCR
				This unit’s remote
				control unit
4	Set the remote control units so they are facing each other,		6	Once the START LED turns off and the LEARNED/TX LED
	then press the button to be learned on this unit’s remote
				lights, release the button on the other remote control unit.
	control unit.	Other remote
	Transmitting windows
		control unit

Light

Approx.

5 cm

This unit’s remote control unit

The indicator stops flashing and the START LED lights.

The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, tape deck, CD recorder, MD recorder, the buttons which can be operated with the preset memory for the DVD, VCR, VDP and TV. For the TV only, however, the buttons in the section indicated “A” on the diagram above can also be “learned”. Use these to “learn” TV channels.

	The two LEDs start
	flashing again.	Light
7	To “learn” other buttons, repeat steps 2 to 6.

8	Once the learning operation is completed, press the
	USE/LEARN selector button again.
	The two LEDs stop flashing and the learning mode is
	cancelled.
	Check that the stored
	codes work properly.

NOTES:

•Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

•If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released.

•If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-903.

•If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored.

To “learn” that code, first perform the resetting operation. (See page 35.)

32