Master Code Switch, Ring Pin | DKS Enterprises 1802, 1803, 1808, 1810

4.5Master Code Switch

The master code switch is left in the off position for normal operation. Turn the master code switch on when setting the system master code. See programming instructions to set the system master code.

If the master code switch is turned on and a new master code is not entered, the system will sound a long tone after approximately 30 seconds. This tone will continue every 30 seconds until a new master code is entered, or until the switch is turned off. After the switch is turned off, the display (1802, 1803, 1810 only) will remain lit for approximately 30 seconds, and then will go off.

4.6Ring Pin

The ring pin-shorting bar is labeled RING on the control board. This shorting pin must be installed to allow the system to answer any calls placed to it. If remote programming or remote relay operation is to be used, the shorting bar must be installed. Removing the shorting bar will cause the system to never answer any call placed to it.

4.7Handset / Hands Free

The handset shorting pins are labeled HS, and the hands free shorting pins are labeled HF on the control board. The shorting bar is factory set and will be placed in the HF position for hands free operation, or will be placed in the HS position for those entry systems ordered with the optional handset. Do not place shorting bars on both the HS and HF pins at the same time.

42

Image 42

DKS Enterprises 1802, 1803, 1808, 1810 owner manual Master Code Switch, Ring Pin, Handset / Hands Free

Contents

1802, 1803, 1808, 1810 Telephone Entry Systems Page Use this manual with the following models only Table of Contents Maintenance and Trouble Shooting Important Notice Listing General Information Features Installation Installation Guidelines ALL Systems Surface Mount 1803 and 1810 Units Surface Mount 1803 and 1810 Units with Recess Box Flush Mount 1803 and 1810 Units Flush Mount Rough-in Box applies to 1803 and 1810 only Flush Mount Trim Ring use with 1803 and 1810 units only 12.0 375 125 DIA 125 SQ 625 7 1802 Surface Mount Only 8 1808 Surface Mount Only Memory Chip Installation Postal Lock Installation Page Wiring 18AWG Main Terminal Description Terminal Description Wiring Description Relay Wiring Typical Controlling a Single Door or Gate Controlling a Gate Operator and Pedestrian Gate or Door Programming from the Keypad Programming from an Offsite LocationProgramming Notes Single or Multiple Systems General ProgrammingMaster Code Relay Strike Time Talk Time Tone Open Numbers Postal Switch Touch-tone / Rotary-dialNumber of Rings to Answer Keypad Function Star * Key Function Phone Number Programming Programming the Directory Code LengthProgramming 7-digit Phone Numbers Programming Area Codes Programming Phone Numbers with Area Code ReferenceDeleting Individual Phone Numbers Delete All Phone Numbers Display / Delete Phone NumbersDisplay Phone Numbers with known Directory Codes Delete Four-Digit Entry Codes Entry Code ProgrammingFour-Digit Entry Code Programming Delete All Four-Digit Entry Codes Delete All Five-Digit Entry Codes Five-Digit Entry Code ProgrammingDelete Five-Digit Entry Codes Five-Digit Entry Code Divide Number Time Functions Programming Time Clock ProgrammingAutomatic Relay Activation Time Zones Four-Digit Entry Code Time Zone Five-Digit Entry Code Time Zone Flash Entry Codes Relay 2 Terminals Click Sensitivity Speaker VolumeFeedback Display Contrast 1802, 1803, 1810 only Master Code Switch Ring PinHandset / Hands Free Guest Instructions Using an Entry CodeGeneral Instructions Responding to a Guest Call Remote Relay Activation System AdministratorRemote Programming Relay Check Entry Code Time Zone Enable / Disable Auto Relay Time Zone Enable / Disable Switch Input Operation Miscellaneous Operating InstructionsLine Sharing Connection to a PBX Areas with 10-digit DialingPage Maintenance Trouble Shooting Sympton Possible Solutions Accessories LOG Tables Name Phone Number Directory Code Entry Alternate Area Code Name Phone Number Directory Code Entry Alternate Area Code Resident Instruction Sheet