1.5 Post Mount
Mount the post base into the concrete before installing the operator.
The post mount installation will allow the operator to be mounted low enough to attach the gate bracket to the lower gate rail if desired.
Note: 2” thick gate Illustrated.
Gate | These measurements will work for standard or | |||
Closed | ||||
convenience open models from 1.1 layout on page 10 ONLY. | ||||
|
|
| ||
|
|
| 90° | |
|
|
|
| |
|
|
|
| |
|
|
| Open Gate | |
|
|
| ||
|
|
|
| |
|
|
| 6” |
| Concrete |
|
| |||||
|
|
|
|
|
| Position |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
25.25” |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| Post Base |
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
| 29” |
|
|
|
|
|
| 10” | ||||
|
|
|
|
|
|
|
|
| ||||
| Conduit |
|
| |||||||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Cable
Interconnection
Operator MUST be level.
Gate Bracket Height
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Arm |
|
| 3” | ||||||
| Low |
| High |
|
|
|
|
| ||||||||||||
|
|
|
| Rotation Area |
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| Volt |
| Volt |
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
| This distance can vary (6” minimum). | ||||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| Depth of the concrete pad is | |||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| determined by soil conditions and | |||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| local building codes. Reinforced | |||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
| concrete recommended. | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18.5”
Run all conduit on the opposite side of the open gate.
1.6 Arm and Gate Bracket Installation
G Brackette
Gate Hinge Pivot Point
30” Crank Arm
Point arms towards gate bracket.
Crank Power Arm
| Arm | Closed Gate |
| cting | |
| onne |
|
C |
| |
60” |
|
|
Assemble arms as shown with the gate in the closed position. The elbow assembly’s flange MUST be on the opposite side of the gate in the closed position. This is the physical stop used to set the open and close limits.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Arms MUST be level. | ||||||
|
|
|
|
|
|
|
|
|
| Top of Crank Arm |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Install gate |
|
| |||||
|
|
|
|
|
|
|
| Elbow |
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
| 3” |
|
| bracket to gate. |
|
| ||||||||||
|
|
| Flange |
|
| Assembly |
|
|
|
| |||||||||||||
|
|
|
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 60” Connecting Arm |
|
|
|
|
|
|
|
|
| Gate Rail | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| 34” |
|
|
|
|
|
|
|
| Varies |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Adjust the locknut on the crank power arm so that it is snug against the washer, but will still allow the crank arm to rotate with little force. This is the operator’s manual release option when the crank arm is unlocked.
Do not secure the elbow assembly to the arms until the arms have been adjusted. (See next page).
Do not insert the locking pin or padlock into the crank arm. It will be installed after arms have been adjusted.
13 |