2.6 Control Wiring

B

•Diagram at right is for illustration purposes. The actual placement of the secondary protection devices is dependent on the specific installation requirements.

•Secondary entrapment protection devices must be installed with this gate operator. This protection may be provided by non-contact or contact sensors, or a combination of both.

•Secondary device wiring shows inputs to the circuit board only. Photo-cells must be supplied with power.

Com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Photo Cells

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

Open direction non-contact sensor.

 

 

 

A

 

 

 

 

A

 

 

 

 

Stops the gate in the open cycle only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gate resumes normal operation when

 

 

 

 

 

 

 

 

the obstruction is cleared.

 

 

 

•Refer to the safety instructions in the front of this manual for more information.

•Controls must be installed a minimum of 10-feet from the gate or installed in such a way that the person using the control

cannot come in contact with the gate or gate operator.

20

•All inputs to the 4502 circuit board are Normally Open (N.O.).

BClose direction non-contact sensor. Reverses gate during the closing cycle only. Holds gate in the full open position until obstruction is cleared.

Note: All stand-alone and telephone entry devices must use a separate power source.

 

 

 

 

When SW 1, switch 5 is OFF,

 

 

 

Com

 

 

 

 

 

 

 

15

terminal 15 will function as a

3 2 1

 

ON

 

 

 

 

 

 

 

normal “Reverse Input” and will

4

 

 

 

 

 

 

 

reverse the gate during a close

6 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cycle if the photo cell beam gets

8 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

obstructed.

SW 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24 Volt

Relay

Com

 

Radio Receiver

 

Limited to 250 ma.

Telephone

Convenience open radio

receiver wiring may differ.

Entry

See section 5.1 for more info.

 

 

 

3-Button Station

 

 

 

 

 

 

Red Open

Key Switch

Green Close

 

 

 

White Com

 

 

 

DoorKing ONLY

1 2

3 4

5

6

7 8

9 10

11

4502

Stand-Alone

Keypad

Stand-Alone

Card Reader

Fire Box

2 1

 

ON

 

 

8 7 6 5 4 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW 1 SW 1, switch 3 must be ON.

Magnetic

Lock

Power (24 Volt DC) and logic output. Power is shut off

.5 sec. prior to gate starting and remains off while gate is opening and in the open position.

24V Com

Com

12

13 14

15 16

17 18

19 20

NC

NO

2 1

 

 

ON

8 7 6 5 4 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW 1

2 1

 

 

ON

8 7 6 5 4 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW 2

POWE

Auxiliary Terminal

1 2 3 4 5 6 7 8

6050-065-L-11-08

19