Manuals / Dynaudio / Home Audio / Speaker

Dynaudio pmn manual Calibrate - AIR BASE, Chained monitors, Air Soft

Models: pmn

1 60

Download 60 pages 63.12 Kb

Page 52

Calibrate - AIR BASE

Air_US_rev_111.qxd 16-12-2004 14:18 Page 50

AIR SOFT

Calibrated Level

Level calibration of the selected monitor.

Relative Level

Preset volume for the selected monitor relative to the calibrated and global volume.

Use Parametric EQ

This will be marked if the Parametric EQ is activated via the PC-IP. Bass and Treble settings will be disabled.

Bass/Treble Range: -6dB to +6dB

Bass and Treble adjustment for the selected monitor. These handles are not available when the Parametric EQ is activated via PC-IP.

Mute

Press to mute the selected monitor.

Solo

Press to solo the selected monitor.

Pink Noise

Press to generate Pink Noise in the selected monitor.

Calibrate - AIR BASE

Mute

Solo

Pink Noise

Via this Calibrate screen, parameters and settings for the Subwoofers are controlled.

The screen is accessed via the Main Screen by holding the cursor above the desired Sub and selecting the hammer icon.

Phase Range: 0-180°

To time-compensate if the Sub is not placed according to the ITU 775 recommendations. There are individual Phase settings for each of the Bass Management Cross-over frequencies. Once set, these are stored as Global settings.

Polarity

Range: 0 or 180 deg.

Mark to activate.

Calibrated Level

Level calibration of the selected monitor.

Relative Level

Preset volume for the selected monitor relative to the calibrated and global volume.

LFE Gain Range: 0 to 14dB

With this parameter you can boost the gain of the LFE channel.

LFE Low Pass Filter

Mark to activate.

Mute

Press to mute the selected Sub.

Solo

Press to solo the selected Sub.

Pink Noise

Press to generate Pink Noise in the selected Sub.

Chained monitors

If several monitors are chained on the same task (e.g. LSur-LSChain) a dropdown menu will be present as illustrated below.

To calibrate a chained monitor simply select from the list.

Chained monitors will also be indicated in the Main screen.

This symbol indicates that there are two monitors chained on this specific position.

50

Image 52

Dynaudio pmn manual Calibrate - AIR BASE, Chained monitors, Air Soft

Contents

Air US rev 111.qxd 16-12-200414 14 Page Air US rev 111.qxd 16-12-200414 14 Page IMPORTANT SAFETY INSTRUCTIONS VoltageLine plug according to standard Air US rev 111.qxd 16-12-200414 14 Page aQUICK SETUP REFERENCE Air US rev 111.qxd 16-12-200414 15 Page bQUICK SETUP REFERENCE Air US rev 111.qxd 16-12-200414 15 Page cTABLE OF CONTENTS Setting up of the AIR SOFTHow To Measure the Sound Pressure Operating AIR SOFTINTRODUCTION This ManualBreak in The Product ConceptRemote Control Common FeaturesThe Master Unit The Slave & Sub UnitsREAR PANEL DESCRIPTION - MASTER Master Unit - Analog I/OSlave/Sub Optional Digital I/O cardOPERATIONAL OVERVIEW Preset locationsMain Display Select Task No taskTHE AIR DISPLAY & SETTING UP Setting up - IntroductionGeneral Setup Procedure parameters using the AIR displaySETUPS Stereo SetupStereo Setup with mono Subs Stereo Setup with stereo Subs5.1 Digital Setup 5.1 Analog SetupSETUPS To set a Master5.3 Analog Setup 5.3 Digital SetupSETUPS 5.1 Dig/6 - Master 6.1 Analog SetupSETUPS Other “Chained” Setups Stereo Setup With Chains on L & RSETUPS 6.1 Digital - 192 kHz 5.1 Digital - 192 kHzSETUPS 5.3 Digital Setup SETUPSWith Bass management “on” WHEN THE MONITORS ARE CONNECTED OverviewPARAMETER DESCRIPTION Basic operation in all menusMain Display Bass ManagementSetup Menu SetupPARAMETER DESCRIPTION Set Monitor TaskPresets In General LFE channel - noteRecall StorePLACING THE MONITORS OverviewPLACING THE MONITORS Free Standing Wall Corner ConsoleFree standing / Neutral Close to wall / WallEvaluation CHECKING - THE PLACEMENT OF THE MONITORSOverview CHECKING - PLACEMENT OF THE MONITORS CALIBRATING - MAIN MONITORS X-CURVESCalibration procedure OverviewPLACING THE SUBWOOFER Placement on the floorPlacement in the corner OverviewCHECKING - SUBWOOFER PLACEMENT OverviewTo Calibrate Bass ManagementLFE Gain PhasePolarity ACOUSTICS - BACKGROUND INFO AcousticsOne sound source, one receiver and no room Only the direct sound is receivedSabines formula ACOUSTICS - BACKGROUND INFOAbsorbers DiffusersACOUSTICS - BACKGROUND INFO Membrane absorbersBACKGROUND INFO - ACOUSTICS Standing WavesACOUSTICS - BACKGROUND INFO Room modesAxial Tangential Radial Air US rev 111.qxd 16-12-200414 17 PageHow to prohibit standing waves ACOUSTICS - BACKGROUND INFOf = c + nbACOUSTICS - BACKGROUND INFO This is also called a 4 π radiationComb Filtering ACOUSTICS - BACKGROUND INFOor + ACOUSTICS - BACKGROUND INFODip frequencies Rear wall cancellation ACOUSTICS - BACKGROUND INFOTHE SUBWOOFER - BACKGROUND INFO The SubwooferBass management L C R Ls Rs Σ SubTHE SUBWOOFER & LFE CHANNEL - BACKGROUND INFO The LFE ChannelAcoustic summation of audio signals DELAYING MONITORSLINE-UP& CALIBRATION LINE-UP& CALIBRATION - BACKGROUND INFO How to measure the sound pressure?Calibration of 5.1 in an ITU-775arrangement THE AIR REMOTE IntroductionPRESET 1/3 AND 2/4 keys VOLUME potentiometerTHE AIR REMOTE REF LEVEL 1-3keysAIR SOFT Press to enter preset listNavigating AIR SOFT Main ToolsVOLUME dialer AIR SOFTNetwork Preset ListAIR SOFT System Setup AIR SOFTCalibrate - Main Monitors Monitor assignmentChained monitors Calibrate - AIR BASEAIR SOFT Reset Procedures MISCELLANEOUSGlobal Parameters Local ParametersCABLES TC LINK Standard Cat-5cablesAES/EBU Standard cables Serial to Cat-5cableAIR TECHNICAL SPECIFICATIONS Air US rev 111.qxd 16-12-200414 18 PageModel FinishAIR TECHNICAL SPECIFICATIONS Air US rev 111.qxd 16-12-200414 18 PageSystem FinishAIR TECHNICAL SPECIFICATIONS SafetyWarranty Air US rev 111.qxd 16-12-200414 18 PageDELAY IN SYSTEM & ERROR MESSAGES ETC Error messages etcCertificate Of Conformity CERTIFICATE OF CONFORMITYAIR AIR AIR AIR AIR BASE AIR BASE AIR REMOTE PRESET LIST Air US rev 111.qxd 16-12-200414 18 Page