Manuals / Eaton Electrical / Computer Equipment / Power Supply

Eaton Electrical Powerware 9315 System Configuration Mode Main Menu, Program Building Alarms

Models: Powerware 9315

1 84

Download 84 pages 23 Kb

Page 59

Communication

7.7 System Configuration

The System Configuration mode allows you to modify special functions in your UPS. These functions include programming of building alarms, customizing building alarm messages, adjusting the nominal output voltage, and scheduling battery tests. The menus provided and their function are described in this section.

7.7.1 System Configuration Mode Main Menu

When the System Configuration mode is selected with a terminal attached, you are prompted to enter the password for this mode:

Please Enter Password:

The default password is EXIDE1. You may modify this password using the change password function in the following menu. When the valid password is entered, the main menu appears:

Program Mode Main Menu

1.Program Building Alarms

2.Program Unit Name

3.Adjust Output Voltage

4.Change Password

5.Battery Test Setup

6.Modify Low Battery Time

7.Exit Program Mode Enter Selection:

7.7.2Program Building Alarms

This menu provides access to all the functions available in the system configuration mode. If 1 is entered at the prompt, you can program the building alarm functions:

Program Building Alarms

1.Enable/Disable Default Functions

2.Customize Alarm Messages

3.Return to Main Menu

Enter Selection:

EATON Powerware® 9315 UPS (200–300 kVA) Operation Manual S 164201036 Rev F powerware.com

7-13

Image 59

Eaton Electrical Powerware 9315 System Configuration Mode Main Menu, Program Building Alarms, Please Enter Password

Contents

Powerware 9315 UPS 200-300 kVA Operation Manual CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSConsignes de sécurité Class A EMC StatementsTable of Contents 1 Introduction2 Getting Started 3 Understanding UPS Operation7 Communication 5 Using the Monitor Panel6 Using Features and Options 4 Starting and Stopping the UPS11-1 11 Using the LOAD OFF Button8 Maintaining the UPS System Table of Contents List of Figures1.1 Conventions Used in This Manual ChapterIntroduction In the United States 1-800-843-9433 or In Canada1-800-461-9166 1.2 For More Information1.3 Getting Help All other countries Call your service representativeC A U T I O N 2.1 Safety WarningsGetting Started D A N G E RFigure 2-1. Typical Powerware 9315 UPS System 2.2 Typical Powerware 9315 UPS SystemFigure 2-2. Main Elements of the UPS System 2.3 Looking Inside the UPS2.4.3 Communication Bays 2.4 UPS Standard Features2.4.1 Monitor Panel 2.4.2 Control Panel2.5.1 Battery 2.5 Options and Accessories2.4.6 Automatic Battery Charge Current Limit 2.4.7 Installation Features2.5.6 Relay Interface Module 2.5.3 Power Distribution Module LV models only2.5.4 Upgrade Capability 2.5.5 Remote Monitor Panel2.5.11 Customer Convenience Outlet 2.5.9 Output Transformer2.5.10 Modem 2.6 Symbols, Controls, and Indicators Chapter 3.1 Normal ModeUnderstanding UPS Operation Understanding UPS Operation Figure 3-1. Path of Current Through the UPS in Normal ModeC A U T I O N 3.2 Bypass ModeFigure 3-2. Path of Current Through the UPS in Bypass Mode Figure 3-3. Path of Current Through the UPS in Battery Mode 3.3 Battery ModeFigure 3-4. Location of the Monitor Panel and the Control Panel 3.4 Monitoring and Controlling UPS OperationUnderstanding UPS Operation This page intentionally left blankC A U T I O N 4.1 Using the Control PanelStarting and Stopping the UPS Chapter4.1.1 To Place the UPS in Normal Mode 4.1.4 To Shut Down Power to the Critical Load While in Bypass Mode 4.1.2 To Shut Down the UPS from Normal Mode4.1.3 To Start the UPS in Bypass Mode Starting and Stopping the UPS This page intentionally left blankFigure 5-1. UPS Monitor Panel Using the Monitor PanelChapter 5.1 Using the LCD Screen C A U T I O N 5.2 Using the Buttons5.3 Adjusting the Contrast 5.4 Using the Load Off Button5.6 Using the Menu Options 5.5 Reading the Status IndicatorsFigure 5-4 shows the Load Amps Meters screen Figure 5-4. Load Amps Meters Screen Using the Monitor PanelSystem Normal Alarm None Notice None Uninterruptible Power System 04 NOV 1997Figure 5-5. Event History Log Screen Figure 5-6. Active System Events Screen Figure 5-7. Unit Statistics Screen Figure 5-8. Mimic Screen Figure 5-9. Time Setup Screen Figure 5-10. Setup Serial Port 1 Screen Chapter Using Features and Options6.1 Building Alarm Monitoring Figure 6-1. External Connections for Building Alarm MonitoringC A U T I O N 6.2 Summary Alarm ContactsFigure 6-2. Summary Alarm Contacts Figure 6-3. Remote Monitor Panel 6.3 Remote Monitor PanelTable 6-1. Optional Monitoring Accessories 6.5 External Battery Disconnect 6.4 Battery CabinetsFigure 6-4. Relay Interface Module 6.6 Relay Interface ModuleFigure 6-5. Supervisory Contact Module 6.7 Supervisory Contact ModuleON GENERATOR This page intentionally left blank Using Features and OptionsChapter Communication7.1 Locating the Communication Bays Figure 7-1. Location of Communication Bays on the UPS Powerware 9315 7.2 X-Slot CardsFigure 7-2. Optional X-Slot Cards 7.3 LanSafe Power Management Software7.4 Connecting Equipment to a Serial Port Figure 7-4. Port 2 DB-25 Pin Assignments Table 7-1. Pin Assignments for Port 1 DB-9Figure 7-3. Port 1 DB-9 Pin Assignments Table 7-2. Pin Assignments for Port 2 DB-25 NOTE Pins 5 and 6 are tied together internallyFigure 7-5. Setup Serial Port 1 Screen 7.5 Configuring the Serial PortsTable 7-3. Available Options for Each Communication Port 7.5.1 Mode7.5.2 Rate 7.5.5 Save 7.5.6 Default Settings7.5.3 Data/Stop 7.5.4 Handshaking7.6.1 Printing Selected Information 7.6 Terminal ModeFigure 7-6. Event History Log 7.6.2 Entire Log - Ctrl+PFigure 7-7. System Meters 7.6.3 Meters Printout - Ctrl+MFigure 7-8. Battery Test Log 7.6.5 Battery Test Printout - Ctrl+B7.6.4 System Information Printout - Ctrl+A Please Enter Password 7.7 System Configuration7.7.1 System Configuration Mode Main Menu 7.7.2 Program Building Alarms4. Enable/Disable Building Alarm 7.7.3 Enable/Disable Default FunctionsEnable/Disable Default Functions 1. Enable/Disable Go To Bypass 2. Enable/Disable Go To UPS 3. Enable/Disable On GeneratorBuilding Alarm Active Message Building Alarm 1 default message 7.7.4 Customize Alarm MessagesCustomize Alarm Messages Enabled on Building Alarm Numbers 2 Enter Building Alarm NumberAdjust Output Voltage Output Voltage Setup Output Voltage Range 456 7.7.6 Adjust Output Voltage7.7.7 Change Password 7.7.5 Program Unit Name7.7.8 Battery Test Setup 7.7.9 Modify Low Battery Time 7.8 Calibration Mode7.9 Computer Mode 7.10 Remote Monitor Mode7.11 Remote Notification Communication This page intentionally left blank7-20 W A R N I N G 8.1 Important Safety InstructionsMaintaining the UPS System ChapterC A U T I O N 8.2 Performing Preventive MaintenanceA V E R T I S S E M E N T W A R N I N G8.3 Maintenance Training Maintaining the UPS System This page intentionally left blankTable 9-2. System Input Product SpecificationsChapter Table 9-1. Model NumbersTable 9-3. System Output Table 9-4. Environmental SpecificationsBattery Charge Table 9-5. Battery SpecificationsBattery Type Nominal BatteryThis page intentionally left blank Product Specifications10.3 System Event Messages Responding to System Events10.1 System Event Horns 10.2 System Event LightsResponding to System Events INVERTER MESSAGES - ALARMSINVERTER MESSAGES - NOTICES 10-2RECTIFIER STATUS MESSAGES RECTIFIER MESSAGES - ALARMSRECTIFIER MESSAGES - COMMANDS RECTIFIER MESSAGES - NOTICES10-4 MONITOR PANEL ALARMSMONITOR PANEL NOTICES W A R N I N G Using the LOAD OFF Button11.1 Using the LOAD OFF Button ChapterC A U T I O N 11.2 Resetting the UPS System after Load OffLIMITED FACTORY WARRANTY FOR THREE-PHASE POWERWARE PRODUCTS WarrantyThis page intentionally left blank WarrantyPage 164201036 F 164201036F