Manuals / Eaton Electrical / Computer Equipment / Power Supply

Eaton Electrical Powerware 9315 operation manual 3. System Output, 4. Environmental Specifications

Models: Powerware 9315

1 84

Download 84 pages 23 Kb

Page 72

Product Specifications

Table 9-3. System Output

Rectifier/Charger Capacity	125%
DC Filtering	Ripple voltage less than 0.5% peak to peak
UPS Output Capacity	100% rated current
Output Voltage Regulation	1% (10% to 100% load)
Output Voltage Adjustment	208 Vac nominal, adjustable from 198 Vac to 218 Vac (60 Hz only)
(Nominal +/–5%)	480 Vac nominal, adjustable from 456 Vac to 504 Vac (60 Hz only)
	600 Vac nominal, adjustable from 570 Vac to 630 Vac (60 Hz only)
	400 Vac nominal, adjustable from 380 Vac to 420 Vac (50/60 Hz)
Output Voltage Harmonic Content	3% max THD, 2% max single (linear load)
Output Voltage Balance	3% for 100% maximum load imbalance
Output Voltage Phase	3° for 100% maximum load imbalance
Displacement
Output Transients	5% for 100% load step or removal
Frequency Regulation	0.01 Hz free running
Synchronous to Bypass	Bypass within voltage limits of +5%, –8% of output setting; bypass within
	±0.5 Hz
Frequency Slew Rate	1 Hz per second maximum (adjustable)
Overload Capability	125% for 10 minutes
	150% for 10 seconds
Maximum Output Capability	300% peak for 10 cycles without bypass
Table 9-4. Environmental Specifications
Operating Temperature	0 to 40°C without derating. However, operating at or near 40°C will
	adversely affect battery life (refer to your battery specifications for more
	information). The recommended operating temperature is 25°C.
Operating Altitude	Maximum 1500m (5000 ft) at 40°C without derating
Storage Temperature	–20 to +70°C (prolonged storage above 40°C will cause rapid battery
	self-discharge)
Relative Humidity (operating and	95% maximum noncondensing
storage)
Acoustical Noise	65 dBA at a 1m distance
EMI Suppression	Meets FCC Regulation 47, Part 15, Subpart J, for class A devices
Electrostatic Discharge (ESD)	Meets IEC 801-2 specifications. Withstands up to 25 kV without damage and
Immunity	with no disturbance or adverse effect to the critical load.

9-2	EATON Powerware® 9315 UPS (200–300 kVA) Operation Manual S 164201036 Rev F powerware.com

Image 72

Eaton Electrical Powerware 9315 operation manual 3. System Output, 4. Environmental Specifications

Contents

Powerware 9315 UPS 200-300 kVA Operation Manual IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Consignes de sécuritéClass A EMC Statements CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS1 Introduction 2 Getting Started3 Understanding UPS Operation Table of Contents5 Using the Monitor Panel 6 Using Features and Options4 Starting and Stopping the UPS 7 Communication11 Using the LOAD OFF Button 8 Maintaining the UPS System11-1 List of Figures Table of ContentsChapter Introduction1.1 Conventions Used in This Manual 1.2 For More Information 1.3 Getting HelpAll other countries Call your service representative In the United States 1-800-843-9433 or In Canada1-800-461-91662.1 Safety Warnings Getting StartedD A N G E R C A U T I O N2.2 Typical Powerware 9315 UPS System Figure 2-1. Typical Powerware 9315 UPS System2.3 Looking Inside the UPS Figure 2-2. Main Elements of the UPS System2.4 UPS Standard Features 2.4.1 Monitor Panel2.4.2 Control Panel 2.4.3 Communication Bays2.5 Options and Accessories 2.4.6 Automatic Battery Charge Current Limit2.4.7 Installation Features 2.5.1 Battery2.5.3 Power Distribution Module LV models only 2.5.4 Upgrade Capability2.5.5 Remote Monitor Panel 2.5.6 Relay Interface Module2.5.9 Output Transformer 2.5.10 Modem2.5.11 Customer Convenience Outlet 2.6 Symbols, Controls, and Indicators 3.1 Normal Mode Understanding UPS OperationChapter Figure 3-1. Path of Current Through the UPS in Normal Mode Understanding UPS Operation3.2 Bypass Mode Figure 3-2. Path of Current Through the UPS in Bypass ModeC A U T I O N 3.3 Battery Mode Figure 3-3. Path of Current Through the UPS in Battery Mode3.4 Monitoring and Controlling UPS Operation Figure 3-4. Location of the Monitor Panel and the Control PanelThis page intentionally left blank Understanding UPS Operation4.1 Using the Control Panel Starting and Stopping the UPSChapter C A U T I O N4.1.1 To Place the UPS in Normal Mode 4.1.2 To Shut Down the UPS from Normal Mode 4.1.3 To Start the UPS in Bypass Mode4.1.4 To Shut Down Power to the Critical Load While in Bypass Mode This page intentionally left blank Starting and Stopping the UPSUsing the Monitor Panel ChapterFigure 5-1. UPS Monitor Panel 5.1 Using the LCD Screen 5.2 Using the Buttons 5.3 Adjusting the Contrast5.4 Using the Load Off Button C A U T I O N5.5 Reading the Status Indicators 5.6 Using the Menu OptionsFigure 5-4 shows the Load Amps Meters screen Using the Monitor Panel System Normal Alarm None Notice NoneUninterruptible Power System 04 NOV 1997 Figure 5-4. Load Amps Meters ScreenFigure 5-5. Event History Log Screen Figure 5-6. Active System Events Screen Figure 5-7. Unit Statistics Screen Figure 5-8. Mimic Screen Figure 5-9. Time Setup Screen Figure 5-10. Setup Serial Port 1 Screen Using Features and Options 6.1 Building Alarm MonitoringFigure 6-1. External Connections for Building Alarm Monitoring Chapter6.2 Summary Alarm Contacts Figure 6-2. Summary Alarm ContactsC A U T I O N 6.3 Remote Monitor Panel Figure 6-3. Remote Monitor PanelTable 6-1. Optional Monitoring Accessories 6.4 Battery Cabinets 6.5 External Battery Disconnect6.6 Relay Interface Module Figure 6-4. Relay Interface Module6.7 Supervisory Contact Module ON GENERATORFigure 6-5. Supervisory Contact Module Using Features and Options This page intentionally left blankCommunication 7.1 Locating the Communication BaysChapter 7.2 X-Slot Cards Figure 7-1. Location of Communication Bays on the UPS Powerware 93157.3 LanSafe Power Management Software 7.4 Connecting Equipment to a Serial PortFigure 7-2. Optional X-Slot Cards Table 7-1. Pin Assignments for Port 1 DB-9 Figure 7-3. Port 1 DB-9 Pin AssignmentsFigure 7-4. Port 2 DB-25 Pin Assignments NOTE Pins 5 and 6 are tied together internally Table 7-2. Pin Assignments for Port 2 DB-257.5 Configuring the Serial Ports Figure 7-5. Setup Serial Port 1 Screen7.5.1 Mode 7.5.2 RateTable 7-3. Available Options for Each Communication Port 7.5.6 Default Settings 7.5.3 Data/Stop7.5.4 Handshaking 7.5.5 Save7.6 Terminal Mode 7.6.1 Printing Selected Information7.6.2 Entire Log - Ctrl+P Figure 7-6. Event History Log7.6.3 Meters Printout - Ctrl+M Figure 7-7. System Meters7.6.5 Battery Test Printout - Ctrl+B 7.6.4 System Information Printout - Ctrl+AFigure 7-8. Battery Test Log 7.7 System Configuration 7.7.1 System Configuration Mode Main Menu7.7.2 Program Building Alarms Please Enter Password7.7.3 Enable/Disable Default Functions Enable/Disable Default Functions 1. Enable/Disable Go To Bypass2. Enable/Disable Go To UPS 3. Enable/Disable On Generator 4. Enable/Disable Building Alarm7.7.4 Customize Alarm Messages Customize Alarm Messages Enabled on Building Alarm Numbers 2Enter Building Alarm Number Building Alarm Active Message Building Alarm 1 default message7.7.6 Adjust Output Voltage 7.7.7 Change Password7.7.5 Program Unit Name Adjust Output Voltage Output Voltage Setup Output Voltage Range 4567.7.8 Battery Test Setup 7.8 Calibration Mode 7.9 Computer Mode7.10 Remote Monitor Mode 7.7.9 Modify Low Battery Time7.11 Remote Notification This page intentionally left blank 7-20Communication 8.1 Important Safety Instructions Maintaining the UPS SystemChapter W A R N I N G8.2 Performing Preventive Maintenance A V E R T I S S E M E N TW A R N I N G C A U T I O N8.3 Maintenance Training This page intentionally left blank Maintaining the UPS SystemProduct Specifications ChapterTable 9-1. Model Numbers Table 9-2. System InputTable 9-4. Environmental Specifications Table 9-3. System OutputTable 9-5. Battery Specifications Battery TypeNominal Battery Battery ChargeProduct Specifications This page intentionally left blankResponding to System Events 10.1 System Event Horns10.2 System Event Lights 10.3 System Event MessagesINVERTER MESSAGES - ALARMS INVERTER MESSAGES - NOTICES10-2 Responding to System EventsRECTIFIER MESSAGES - ALARMS RECTIFIER MESSAGES - COMMANDSRECTIFIER MESSAGES - NOTICES RECTIFIER STATUS MESSAGESMONITOR PANEL ALARMS MONITOR PANEL NOTICES10-4 Using the LOAD OFF Button 11.1 Using the LOAD OFF ButtonChapter W A R N I N G11.2 Resetting the UPS System after Load Off C A U T I O NWarranty LIMITED FACTORY WARRANTY FOR THREE-PHASE POWERWARE PRODUCTSWarranty This page intentionally left blankPage 164201036F 164201036 F