Manuals / Emerson / Personal Care / Oxygen Equipment

Emerson 51-DO-03, 51-DO-04 Attaching the air compressor enclosure to the handrail

Models: 51-DO-04 51-DO-03 DO-04 DO-03

1 70

Download 70 pages 4.9 Kb

Page 16

MODEL DO-03/04	SECTION 2.0
	INSTALLATION

FIGURE 2-3. Attaching the air compressor enclosure to the handrail

FIGURE 2-4. Assembling and attaching the handrail mounting assembly.

The spring pin (not shown) shipped with the handrail mounting assembly is not used.

10

Image 16

Emerson 51-DO-03, 51-DO-04 instruction manual Attaching the air compressor enclosure to the handrail

Contents

Dissolved Oxygen Measurement System with Air Blast Cleaner Model DO-03/04 Essential Instructions Page Model DO-03/04 Measuring System Section Title 10.0 List of Tables11.0 Section Title List of FiguresIii Section Specifications Features and Benefits Power Repeatability ±0.05 ppm 25CRFI/EMI EN-61326 Output Accuracy ± 0.05 mA Maximum distance between compressor and sensor Maximum continuous pressure 50 psig 446 kPa absMaterials of Construction Analyzer dimensions Enclosure dimensions Description Power required selection9240048-00 Tag, stainless steel, specify marking Section Installation InstallationUnpacking and Inspection Model or part number Description Installing the handrail mounting assembly Installing the air compressor enclosureAssembling the pipe and pipe clamp Attaching the pipe boom to the handrail mounting assembly Installing the sensor in the washer head assemblyAssembling the washer head and pipe boom Attaching the air compressor enclosure to the handrail Installing the sensor in the washer head assembly POWER, ALARM, and Output Wiring Section WiringGeneral 454EPH02 Section Section Wiring the Oxygen Sensor Sensor WiringGeneral Alarm Status Section Display and OperationDisplay KEY Functions and Control Section Software Configuration Menu Tree for the 54eA Analyzer On following Main Menu Calibrate See Diagnostic Variable see Program Settings List Choices Factory Settings Setpoints Choices Factory Settings Configure Choices Factory Settings Alarm setpoints Alarm 1 setpointAlarm 2 setpoint Alarm 3 setpoint MA 0.00 ppm 20 mA 20.00 ppm Output 1 12.00 mA Ranging the Outputs Simulated tests Test alarm 1 OpenTest output Outputs Alarms DisplayMeasure Oxygen Meas units ppm Temp units C Output 1 mA Output 2 mA Display contrast Timeout OnLanguage English Display left Display right Out Output 1 control OutputsOutput Measurement Output 1 Control Output 1 SetupRange 4-20 mA Dampen 0 sec Hold Last Value Configure Alarm 1 controlAlarm 1 setup Alarm 2 control Changing Alarm Parameters Alarm 1 control Alarm 1 setupAlarm Low Activate Process Alarm Fault Feed limit DisableTimeout 3600 sec Alarm 4 setup Alarm 4 setup Feed limit timer Interval timerTimer Disable Timer Time activated Interval 24.0 hr Interval timer setup Temperature Compensation and Temperature Units Temp comp AutoTemp units C Temp comp Manual Temp units C 60 Hz Noise Reduction Bar units mm Hg Bar meas AutoBarometric Pressure Main sensor cal Salinity 0.0 o/oo Noise rejection Main sensor cal Security Security Condition Definitions Analyzer Mode PriorityAction Definitions Section Calibration Temperature Introduction Adjust temp + 025.1 C Temperature Calibration Section Calibration Dissolved Oxygen Sensor Current as a Function Dissolved Oxygen Concentration Sensor must be in zero solution Zeroing the Sensor Stabilizing . . . Wait Calibrating the Sensor in AIR Section Calibrate 8.32 ppm Calibrating the Sensor Against a Standard Instrument Zero main sensor Adjust temperature Calibrate main sensorStandardize Calibrating Barometric Pressure Section Calibration Current Outputs Trimming the Outputs Section Maintenance Replacement PartsCleaning the membrane Replacing electrolyte solution and membrane Section Power Fuse Spare Parts Replacement Parts Location Part Number Description AIR Blast Sensor Washer Section Troubleshooting Troubleshooting When a Fault Message is ShowingFault message Explanation See Section Overview Temperature error low or high High input currentCheck sensor zero Sense line open Problem See Section Troubleshooting When no Fault Message is Showing OxygenZero current is too high Zero reading Is unstable Possible error warning during in-process calibrationBarometric pressure reading is too high or too low Process readings are erratic Readings driftSensor does not respond to changes in oxygen level Oxygen readings are too low Troubleshooting not Related to Measurement Problems Problem ActionSimulating Inputs Dissolved Oxygen Sensor Polarizing Voltage Resistance Expected current Simulating Temperature Simulating temperature Section Return of Material General Return of Materials Request Sensor or Circuit Board only Warranty Specifications subject to change without notice