Manuals / Emerson / Personal Care / Oxygen Equipment

Emerson 51-DO-03, 51-DO-04 Section Software Configuration, Menu Tree for the 54eA Analyzer

Models: 51-DO-04 51-DO-03 DO-04 DO-03

1 70

Download 70 pages 4.9 Kb

Page 24

Image 24

MODEL DO-03/04	SECTION 5.0
	SOFTWARE CONFIGURATION

SECTION 5.0

SOFTWARE CONFIGURATION

Figure 5-1 is an outline of the menu structure.

FIGURE 5-1. Menu Tree for the 54eA Analyzer

Main

Menu

Calibrate

Diagnostic Variables

Calibrate main sensor

Zero main sensor

Adjust temperature

Output trim

Main measurement

Main sensor current

Sensitivity (μA/ppm)

Zero current

Barometric pressure

Noise rejection

Software version

Device ID

Program (see following page)

18

Image 24

Emerson 51-DO-03, 51-DO-04 instruction manual Section Software Configuration, Menu Tree for the 54eA Analyzer

Contents

Dissolved Oxygen Measurement System with Air Blast Cleaner Model DO-03/04 Essential Instructions Page Model DO-03/04 Measuring System Section Title List of Tables 10.011.0 List of Figures Section TitleIii Section Specifications Features and Benefits Power Repeatability ±0.05 ppm 25CRFI/EMI EN-61326 Output Accuracy ± 0.05 mA Maximum continuous pressure 50 psig 446 kPa abs Maximum distance between compressor and sensorMaterials of Construction Analyzer dimensions Enclosure dimensions Power required selection Description9240048-00 Tag, stainless steel, specify marking Section Installation InstallationUnpacking and Inspection Model or part number Description Installing the air compressor enclosure Installing the handrail mounting assemblyAssembling the pipe and pipe clamp Installing the sensor in the washer head assembly Attaching the pipe boom to the handrail mounting assemblyAssembling the washer head and pipe boom Attaching the air compressor enclosure to the handrail Installing the sensor in the washer head assembly Section Wiring POWER, ALARM, and Output WiringGeneral 454EPH02 Section Section Sensor Wiring Wiring the Oxygen SensorGeneral Alarm Status Section Display and OperationDisplay KEY Functions and Control Section Software Configuration Menu Tree for the 54eA Analyzer On following Main Menu Calibrate See Diagnostic Variable see Program Settings List Choices Factory Settings Setpoints Choices Factory Settings Configure Choices Factory Settings Alarm setpoints Alarm 1 setpointAlarm 2 setpoint Alarm 3 setpoint MA 0.00 ppm 20 mA 20.00 ppm Output 1 12.00 mA Ranging the Outputs Test alarm 1 Open Simulated testsTest output Outputs Alarms DisplayMeasure Oxygen Meas units ppm Display contrast Timeout On Temp units C Output 1 mA Output 2 mALanguage English Display left Display right Out Outputs Output 1 controlOutput Measurement Output 1 Setup Output 1 ControlRange 4-20 mA Dampen 0 sec Hold Last Value Configure Alarm 1 controlAlarm 1 setup Alarm 2 control Changing Alarm Parameters Alarm 1 control Alarm 1 setupAlarm Low Activate Process Alarm Fault Feed limit DisableTimeout 3600 sec Alarm 4 setup Alarm 4 setup Feed limit timer Interval timerTimer Disable Timer Time activated Interval 24.0 hr Interval timer setup Temperature Compensation and Temperature Units Temp comp AutoTemp units C Temp comp Manual Temp units C 60 Hz Noise Reduction Bar meas Auto Bar units mm HgBarometric Pressure Main sensor cal Salinity 0.0 o/oo Noise rejection Main sensor cal Security Security Analyzer Mode Priority Condition DefinitionsAction Definitions Section Calibration Temperature Introduction Adjust temp + 025.1 C Temperature Calibration Section Calibration Dissolved Oxygen Sensor Current as a Function Dissolved Oxygen Concentration Sensor must be in zero solution Zeroing the Sensor Stabilizing . . . Wait Calibrating the Sensor in AIR Section Calibrate 8.32 ppm Calibrating the Sensor Against a Standard Instrument Zero main sensor Adjust temperature Calibrate main sensorStandardize Calibrating Barometric Pressure Section Calibration Current Outputs Trimming the Outputs Section Maintenance Replacement PartsCleaning the membrane Replacing electrolyte solution and membrane Section Power Fuse Spare Parts Replacement Parts Location Part Number Description AIR Blast Sensor Washer Section Troubleshooting Troubleshooting When a Fault Message is ShowingFault message Explanation See Section Overview Temperature error low or high High input currentCheck sensor zero Sense line open Troubleshooting When no Fault Message is Showing Oxygen Problem See SectionZero current is too high Possible error warning during in-process calibration Zero reading Is unstableBarometric pressure reading is too high or too low Process readings are erratic Readings driftSensor does not respond to changes in oxygen level Oxygen readings are too low Troubleshooting not Related to Measurement Problems Problem ActionSimulating Inputs Dissolved Oxygen Sensor Polarizing Voltage Resistance Expected current Simulating Temperature Simulating temperature Section Return of Material General Return of Materials Request Sensor or Circuit Board only Warranty Specifications subject to change without notice