Installation, Important Notice | Enterasys Networks 9034310-01

3

Installation

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Important Notice

Read the Release Notes shipped with the DFE-Platinum module to check for any exceptions to the supported features and operation documented in this guide.

This chapter provides the instructions to install the DFE‐Platinum 2G4082‐25 module. Follow the order of the sections listed below to correctly install the module.

For information about...	Refer to page...

Unpacking the DFE-Platinum Module	3-2

Installing Optional Network Expansion Modules	3-2

Installing Module into Matrix E7 or N7 Chassis	3-2

Installing Module into Matrix N1, N3, or N5 Chassis	3-5

Connecting to the Network	3-6

Connecting to COM Port for Local Management	3-10

Completing the Installation of a New System	3-15

Matrix DFE-Platinum Series Installation Guide 3-1

Image 25

Enterasys Networks 9034310-01, 2G4082-25 manual Installation, Important Notice

Contents

Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents Index Appendix a SpecificationsTables Who Should Use This Guide About This GuideImportant Notice Related Documents How to Use This Guide Getting Help Conventions Used in This Guide Getting Help Overview of DFE Series Capabilities Introduction 2G4082-25 DFE-Platinum Module DFE Switch Configuration Using CLI Commands Switch Configuration Using WebViewNetwork Expansion Module NEM Option Connectivity Secure Networks Policy Support Lanview Diagnostic LEDsStandards Compatibility Lanview Diagnostic LEDs Introduction Link Aggregation Network Requirements 100BASE-TX Network 10BASE-T Network1000BASE-T Network 1000BASE-SX/LX/ELX Network Installation Installing Module into Matrix E7 or N7 Chassis Installing Optional Network Expansion ModulesUnpacking the DFE-Platinum Module Preparation Installation Card guides Installing Module into Matrix N1, N3, or N5 Chassis Connecting UTP Cables Connecting to the Network Connecting a Twisted Pair Segment to the DFE-Platinum Module RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 What Is Needed Connecting to COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Connecting an IBM PC or Compatible Connecting to a VT Series Terminal Connecting a VT Series Terminal Connecting to a Modem DB9 Adapter Wiring and Signal Assignments Modem Port Adapter Wiring and Signal Diagram First-Time Log-In Using a Console Port Connection Completing the Installation of a New System 11 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Using Lanview TroubleshootingAbout the Management Mgmt LED Viewing the Receive and Transmit Activity LED Alternating 67% on, 33% off Series Configuration Guide for proper setup Troubleshooting Checklist Overview of DFE-Platinum Module Shutdown Procedure Recommended Shutdown Procedure DFE-Platinum Module Specifications Specifications Regulatory Compliance COM Port Pinout Assignments Setting the Mode Switches Mode Switch Bank Settings Optional InstallationsRequired Tools Figure B-1 Mode Switch Location on 2G4082-25 Memory Locations and Replacement Procedures Location of Memory Modules Flash Dimm Replacement ProcedureRemoving the Dimm from 2G4082-25 Figure B-3 NEM Removal and Dimm Connector Location Dimm Installing the Dimm Installing the Dram Simm Dram Simm Replacement ProcedureRemoving the Dram Simm Figure B-7 Installing the Dram Simm Page Numerics Index Index-2