Enterasys Networks 2G4082-25, 9034310-01 Connecting to a Modem

Connecting to COM Port for Local Management Connecting to Modem

3-12 Installation

Figure 3-9 Connecting a VT Series Terminal

Connecting to a Modem

ToconnectamodemtoanEnterasys NetworksDFE‐PlatinummoduleCOMport(Figure 3‐10),

useaUTPstraight‐throughcablewithRJ45connectorsandanRJ45‐to‐DB25maleadapter,and

proceedasfollows:

1. ConnecttheRJ45connectoratoneendoftheUTPstraight‐throughcabletotheCOMportof

theDFE‐Platinummodule.

2. PlugtheRJ45connectorattheotherendoftheUTPstraight‐throughcableintotheRJ45‐to‐

DB25modemadapter.

3. ConnecttheRJ45‐to‐DB25adaptertothecommunicationsportonthemodem.

4. Turnonthemodem.

5. WithaPCconnectedtoaremotemodem,youcanconfiguretheswitchremotely.To

accomplishthis,youmustconfigureyourPCVTemulationpackagewiththefollowing

parameters.

6. Whentheseparametersareset,theLocalManagementpasswordscreenwilldisplay.Referto

theEnterasysMatrixDFE‐Diamond/PlatinumSeriesConfigurationGuideforfurtherinformation.

1UTP straight-through cable with RJ45 connectors 3RJ45-to-DB25 VT adapter

2RJ45 COM port 4VT series terminal

ÀÂÃ

2G4082-25

Gb ENET

COM

OFFLINE/

RESET

MGMT CPU

1

2

GROUP

SELECT

1X

11X 12X

G

R

O

U

P

1

GROUP

1

2

3

4

5

6

7

8

9

10

11

Á

Parameter Setting

Mode 7 Bit Control

Transmit Transmit=9600

Bits Parity 8 Bits, No Parity

Stop Bit 1 Stop Bit

Contents

Main Page Notice Regulatory Compliance Information Page Supplement to Product Instructions 50 VCCI Notice BSMI EMC Statement Taiwan Safety Information Class 1 Laser Transceivers Declaration of Conformity ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. Page Page Contents About This Guide Chapter 1: Introduction Chapter 2: Network Requirements Chapter 3: Installation Appendix A: Specifications Appendix B: Mode Switch Bank Settings and Optional Installations Index Figures Tables About This Guide Who Should Use This Guide Important Notice How to Use This Guide Related Documents Conventions Used in This Guide Getting Help Page Introduction Overview of DFE Series Capabilities DFE-Platinum Module 2G4082-25 DFE-Platinum Module Matrix DFE-Platinum Series Installation Guide 1-3 Figure 1-1 DFE-Platinum 2G4082-25Module Network Expansion Module (NEM) Option Connectivity Management Switch Configuration Using WebView Switch Configuration Using CLI Commands Secure Networks Policy Support Standards Compatibility LANVIEW Diagnostic LEDs Page Network Requirements Link Aggregation 10BASE-T Network 100BASE-TX Network 1000BASE-T Network 1000BASE-SX/LX/ELX Network Installation Important Notice For information about... Refer to page... Unpacking the DFE-Platinum Module Installing Optional Network Expansion Modules Installing Module into Matrix E7 or N7 Chassis Preparation Installation Installing Module into MatrixE7 or N7 Chassis 3-4 Installation Gb ENET Installing Module into Matrix N1, N3, or N5 Chassis Connecting to the Network 3-6 Installation Figure 3-2 Installing Module into N3, N1, or N5 Chassis (N3 shown) Gb ENET Connecting to the Network Connecting UTP Cables FAN STATUS 7C203-1 REDUNDANCY PWR 100-125V~12.0A 200-240V~6.0A 50/60 Hz Page Page Page Connecting to COM Port for Local Management What Is Needed Connecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Connecting to a Modem Pin Out Descriptions Connecting to COM Port for Local Management Adapter Wiring and Signal Assignments Matrix DFE-Platinum Series Installation Guide 3-13 Figure 3-10 Connecting to a Modem RJ45 Connector (Female) 2G4082-25 VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25 Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation of a New System First-Time Log-In Using a Console Port Connection Logging in with an Administratively-Configured User Account Troubleshooting Using LANVIEW About the Management (MGMT) LED Viewing the Receive and Transmit Activity Figure 4-1 LANVIEW LEDs Tabl e 41describestheLEDindicationsandprovidesrecommendedactionsasappropriate. Table 4-1 LANVIEW LEDs LED Color State Recommended Action Table 4-1 LANVIEW LEDs (continued) LED Color State Recommended Action Troubleshooting Checklist Overview of DFE-Platinum Module Shutdown Procedure Table 4-2 Troubleshooting Checklist (continued) Problem Possible Cause Recommended Action Recommended Shutdown Procedure Last Resort Shutdown Procedure A Specifications DFE-Platinum Module Specifications COM Port Pinout Assignments Regulatory Compliance B Mode Switch Bank Settings and Optional Installations Required Tools Setting the Mode Switches B-2 Mode Switch Bank Settings and Optional Installations Memory Locations and Replacement Procedures 1Mode switch bank 12345678 ON Matrix DFE-Platinum Series Hardware Installation Guide B-3 Location of Memory Modules 1Flash DIMM 2DRAM SIMM 3Main PC board Flash DIMM Replacement Procedure Removing the DIMM from 2G4082-25 B-4 Mode Switch Bank Settings and Optional Installations Figure B-3 NEM Removal and DIMM Connector Location 7G-6MGBIC-A 3. RotatetheDIMMupwards,thenremoveitfromtheconnectorfingers. 1Connector arms 2DIMM 3 Connector fingers Page DRAM SIMM Replacement Procedure Removing the DRAM SIMM Installing the DRAM SIMM Page Page Index Numerics C D E