6H302-48
6H302-48 and 6H303-48 Fast Ethernet User’s Guide
6H303-48
FAST ENET
Page
Order Number 9033387-05 October
Enterasys Networks, Inc 35 Industrial Way Rochester, NH
INDUSTRY CANADA NOTICE
FCC NOTICE
VCCI NOTICE
CLASS A ITE NOTICE
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT
ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENT
CAREFULLY READ THIS LICENSE AGREEMENT
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU
DECLARATION OF CONFORMITY
Page
ABOUT THIS GUIDE
Contents
Contents
viii Contents
INDEX
Figures
Figures
x Tables
Tables
About This Guide
USING THIS GUIDE
Important Notices
RELATED DOCUMENTS
STRUCTURE OF THIS GUIDE
Matrix E7 Overview and Setup Guide
6C105 SmartSwitch 6000 Overview and Setup Guide
The guide uses the following conventions
DOCUMENT CONVENTIONS
Document Conventions
About This Guide
GETTING HELP
Important Notice
Introduction
Figure 1-1 6H302-48 and 6H303-48 Modules
Group Select Switch Port Status LEDs Group Select LEDs Network Ports
1-2 Introduction
Network Ports
1.2 RUNTIME IP ADDRESS DISCOVERY
1.1 CONNECTIVITY
1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION
1.4 SMARTTRUNK
1.6 BROADCAST SUPPRESSION
1.5 REMOTE MONITORING RMON
1.7 PORT/VLAN REDIRECT FUNCTIONS
Remote Monitoring RMON
1.9 FLOW CONTROL
1.8 TRAFFIC RATE LIMITING
Installation in the Matrix E7 6C107 Chassis
1.10 GARP SWITCH OPERATION
1.11 802.1 PORT PRIORITY
1.12 DISTRIBUTED CHASSIS MANAGEMENT
Installation in the SmartSwitch 6000 6C105 Chassis
1.14 SWITCHING OPTIONS
1.13 MANAGEMENT
1.15 STANDARDS COMPATIBILITY
1.16 LANVIEW DIAGNOSTIC LEDs
Standards Compatibility
1-8 Introduction
Network Requirements
2.1 SMARTTRUNK FEATURE
2.2 10BASE-T NETWORK
100BASE-TX Network
2.3 100BASE-TX NETWORK
2-2 Network Requirements
Installation
3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS
3.2 INSTALLING OPTIONAL FLASH UPGRADE
3.1 UNPACKING THE MODULE
To install a module, refer to Figure 3-1 and proceed as follows
Figure 3-1 Installing a Module into the Matrix E7 Chassis
Installing the Module into the Matrix E7 Chassis
3-4 Installation
Backplane Connectors Slot Number
3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS
Figure 3-2 Installing a Module into the 6C105 Chassis
Installing the Module into the 6C105 Chassis
3-6 Installation
338702
3.5.1 Connecting UTP Cables to the 6H302-48
3.5 CONNECTING TO THE NETWORK
Group Select
Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48
Button
Figure 3-4 Crossover Cable RJ45 Pinouts
3.5.2 Connecting UTP Cables to the 6H303-48
Figure 3-5 Straight-Through Cable RJ45 Pinouts
Screw
Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48
Screw Hole
ScrewScrew Hole
Completing the Installation
3.6 COMPLETING THE INSTALLATION
Installation
Page
4.1 USING LANVIEW
Troubleshooting
Viewing Receive and Transmit Activity
4-2 Troubleshooting
Using LANVIEW
Figure 4-1 LANVIEW LEDs both modules
Power off
Using LANVIEW
Ensure chassis has adequate power
Solid. Resetting, normal
4-4 Troubleshooting
Using LANVIEW
Table 4-1 LANVIEW LEDs Continued
Color State
Troubleshooting Checklist
4.2 TROUBLESHOOTING CHECKLIST
Table 4-2 Troubleshooting Checklist
Problem
Table 4-2 Troubleshooting Checklist Continued
Troubleshooting Checklist
Problem
4-6 Troubleshooting
Figure 4-2 RESET Button both modules
4.3 USING THE RESET BUTTON
Page
A.1 6H302-48 / 6H303-48 SPECIFICATIONS
Specifications
Processors/Memory
Physical Properties
Input/Output Ports
Environmental Requirements
6H302-48
6H303-48
A.3 REGULATORY COMPLIANCE
A.2 COM PORT PINOUT ASSIGNMENTS
Table A-2 COM Port Pin Assignments
Table A-3 Compliance Standards
Page
B.1 REQUIRED TOOLS
Mode Switch Bank Settings and Options
B.2 SETTING THE MODE SWITCHES
DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file
B.3.1 Locating the FLASH Module
B.3 FLASH UPGRADE
B.3.2 Installing the FLASH Module
Page
Numerics
Index
Index-2