Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H302-48 manual

Models: 6H302-48

1 58

Download 58 pages 11 Kb

Page 50

Image 50

Enterasys Networks 6H302-48 manual

Contents

6H303-48 6H302-48 and 6H303-48 Fast Ethernet User’s Guide6H302-48 FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH Order Number 9033387-05 OctoberVCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CLASS A ITE NOTICECAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page Contents ContentsABOUT THIS GUIDE INDEX viii ContentsFigures FiguresTables x TablesImportant Notices USING THIS GUIDEAbout This Guide Matrix E7 Overview and Setup Guide STRUCTURE OF THIS GUIDERELATED DOCUMENTS 6C105 SmartSwitch 6000 Overview and Setup GuideDocument Conventions DOCUMENT CONVENTIONSThe guide uses the following conventions About This GuideGETTING HELP Introduction Important Notice1-2 Introduction Group Select Switch Port Status LEDs Group Select LEDs Network PortsFigure 1-1 6H302-48 and 6H303-48 Modules Network Ports1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.1 CONNECTIVITY1.2 RUNTIME IP ADDRESS DISCOVERY 1.4 SMARTTRUNK1.7 PORT/VLAN REDIRECT FUNCTIONS 1.5 REMOTE MONITORING RMON1.6 BROADCAST SUPPRESSION Remote Monitoring RMON1.8 TRAFFIC RATE LIMITING 1.9 FLOW CONTROL1.11 802.1 PORT PRIORITY 1.10 GARP SWITCH OPERATIONInstallation in the Matrix E7 6C107 Chassis 1.12 DISTRIBUTED CHASSIS MANAGEMENT1.13 MANAGEMENT 1.14 SWITCHING OPTIONSInstallation in the SmartSwitch 6000 6C105 Chassis Standards Compatibility 1.16 LANVIEW DIAGNOSTIC LEDs1.15 STANDARDS COMPATIBILITY 1-8 Introduction2.2 10BASE-T NETWORK 2.1 SMARTTRUNK FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.1 UNPACKING THE MODULE 3.2 INSTALLING OPTIONAL FLASH UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS To install a module, refer to Figure 3-1 and proceed as follows 3-4 Installation Installing the Module into the Matrix E7 ChassisFigure 3-1 Installing a Module into the Matrix E7 Chassis Backplane Connectors Slot Number3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS 3-6 Installation Installing the Module into the 6C105 ChassisFigure 3-2 Installing a Module into the 6C105 Chassis 3387023.5 CONNECTING TO THE NETWORK 3.5.1 Connecting UTP Cables to the 6H302-48Button Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48Group Select Figure 3-5 Straight-Through Cable RJ45 Pinouts 3.5.2 Connecting UTP Cables to the 6H303-48Figure 3-4 Crossover Cable RJ45 Pinouts Screw Hole Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48Screw ScrewScrew HoleInstallation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Page Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW Figure 4-1 LANVIEW LEDs both modules Using LANVIEW4-2 Troubleshooting Ensure chassis has adequate power Using LANVIEWPower off Solid. Resetting, normalTable 4-1 LANVIEW LEDs Continued Using LANVIEW4-4 Troubleshooting Color StateTable 4-2 Troubleshooting Checklist 4.2 TROUBLESHOOTING CHECKLISTTroubleshooting Checklist ProblemProblem Troubleshooting ChecklistTable 4-2 Troubleshooting Checklist Continued 4-6 Troubleshooting4.3 USING THE RESET BUTTON Figure 4-2 RESET Button both modulesPage Processors/Memory SpecificationsA.1 6H302-48 / 6H303-48 SPECIFICATIONS Physical Properties6H302-48 Environmental RequirementsInput/Output Ports 6H303-48Table A-2 COM Port Pin Assignments A.2 COM PORT PINOUT ASSIGNMENTSA.3 REGULATORY COMPLIANCE Table A-3 Compliance StandardsPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file B.3 FLASH UPGRADE B.3.1 Locating the FLASH ModuleB.3.2 Installing the FLASH Module Page Index NumericsIndex-2