Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H302-48 manual

Models: 6H302-48

1 58

Download 58 pages 11 Kb

Page 8

Image 8

Enterasys Networks 6H302-48 manual

Contents

6H302-48 and 6H303-48 Fast Ethernet User’s Guide 6H302-486H303-48 FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH Order Number 9033387-05 OctoberFCC NOTICE INDUSTRY CANADA NOTICEVCCI NOTICE CLASS A ITE NOTICECAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page Contents ContentsABOUT THIS GUIDE INDEX viii ContentsFigures FiguresTables x TablesImportant Notices USING THIS GUIDEAbout This Guide STRUCTURE OF THIS GUIDE RELATED DOCUMENTSMatrix E7 Overview and Setup Guide 6C105 SmartSwitch 6000 Overview and Setup GuideDOCUMENT CONVENTIONS The guide uses the following conventionsDocument Conventions About This GuideGETTING HELP Introduction Important NoticeGroup Select Switch Port Status LEDs Group Select LEDs Network Ports Figure 1-1 6H302-48 and 6H303-48 Modules1-2 Introduction Network Ports1.1 CONNECTIVITY 1.2 RUNTIME IP ADDRESS DISCOVERY1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.4 SMARTTRUNK1.5 REMOTE MONITORING RMON 1.6 BROADCAST SUPPRESSION1.7 PORT/VLAN REDIRECT FUNCTIONS Remote Monitoring RMON1.8 TRAFFIC RATE LIMITING 1.9 FLOW CONTROL1.10 GARP SWITCH OPERATION Installation in the Matrix E7 6C107 Chassis1.11 802.1 PORT PRIORITY 1.12 DISTRIBUTED CHASSIS MANAGEMENT1.13 MANAGEMENT 1.14 SWITCHING OPTIONSInstallation in the SmartSwitch 6000 6C105 Chassis 1.16 LANVIEW DIAGNOSTIC LEDs 1.15 STANDARDS COMPATIBILITYStandards Compatibility 1-8 Introduction2.2 10BASE-T NETWORK 2.1 SMARTTRUNK FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.1 UNPACKING THE MODULE 3.2 INSTALLING OPTIONAL FLASH UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS To install a module, refer to Figure 3-1 and proceed as follows Installing the Module into the Matrix E7 Chassis Figure 3-1 Installing a Module into the Matrix E7 Chassis3-4 Installation Backplane Connectors Slot Number3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS Installing the Module into the 6C105 Chassis Figure 3-2 Installing a Module into the 6C105 Chassis3-6 Installation 3387023.5 CONNECTING TO THE NETWORK 3.5.1 Connecting UTP Cables to the 6H302-48Button Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48Group Select Figure 3-5 Straight-Through Cable RJ45 Pinouts 3.5.2 Connecting UTP Cables to the 6H303-48Figure 3-4 Crossover Cable RJ45 Pinouts Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48 ScrewScrew Hole ScrewScrew HoleInstallation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Page Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW Figure 4-1 LANVIEW LEDs both modules Using LANVIEW4-2 Troubleshooting Using LANVIEW Power offEnsure chassis has adequate power Solid. Resetting, normalUsing LANVIEW 4-4 TroubleshootingTable 4-1 LANVIEW LEDs Continued Color State4.2 TROUBLESHOOTING CHECKLIST Troubleshooting ChecklistTable 4-2 Troubleshooting Checklist ProblemTroubleshooting Checklist Table 4-2 Troubleshooting Checklist ContinuedProblem 4-6 Troubleshooting4.3 USING THE RESET BUTTON Figure 4-2 RESET Button both modulesPage Specifications A.1 6H302-48 / 6H303-48 SPECIFICATIONSProcessors/Memory Physical PropertiesEnvironmental Requirements Input/Output Ports6H302-48 6H303-48A.2 COM PORT PINOUT ASSIGNMENTS A.3 REGULATORY COMPLIANCETable A-2 COM Port Pin Assignments Table A-3 Compliance StandardsPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file B.3 FLASH UPGRADE B.3.1 Locating the FLASH ModuleB.3.2 Installing the FLASH Module Page Index NumericsIndex-2