Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H302-48 manual B.3 FLASH UPGRADE, B.3.1 Locating the FLASH Module

Models: 6H302-48

1 58

Download 58 pages 11 Kb

Page 54

B.3 FLASH UPGRADE

FLASH Upgrade

B.3 FLASH UPGRADE

FLASH upgrade is available for the switch to expand from 8 to 16 MB. This section explains how to locate and add/replace the FLASH module. For details on getting help, refer to “Getting Help,” in About This Guide.

B.3.1 Locating the FLASH Module

Figure B-2shows the location of the FLASH module.

Figure B-2 FLASH Module Location

Flash Module

Memory Board

3387_10

B-4Mode Switch Bank Settings and Options

Image 54

Enterasys Networks 6H302-48 manual B.3 FLASH UPGRADE, B.3.1 Locating the FLASH Module

Contents

6H303-48 6H302-48 and 6H303-48 Fast Ethernet User’s Guide6H302-48 FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH Order Number 9033387-05 OctoberVCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CLASS A ITE NOTICEENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page Contents ABOUT THIS GUIDEContents INDEX viii ContentsFigures FiguresTables x TablesUSING THIS GUIDE About This GuideImportant Notices Matrix E7 Overview and Setup Guide STRUCTURE OF THIS GUIDERELATED DOCUMENTS 6C105 SmartSwitch 6000 Overview and Setup GuideDocument Conventions DOCUMENT CONVENTIONSThe guide uses the following conventions About This GuideGETTING HELP Introduction Important Notice1-2 Introduction Group Select Switch Port Status LEDs Group Select LEDs Network PortsFigure 1-1 6H302-48 and 6H303-48 Modules Network Ports1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.1 CONNECTIVITY1.2 RUNTIME IP ADDRESS DISCOVERY 1.4 SMARTTRUNK1.7 PORT/VLAN REDIRECT FUNCTIONS 1.5 REMOTE MONITORING RMON1.6 BROADCAST SUPPRESSION Remote Monitoring RMON1.8 TRAFFIC RATE LIMITING 1.9 FLOW CONTROL1.11 802.1 PORT PRIORITY 1.10 GARP SWITCH OPERATIONInstallation in the Matrix E7 6C107 Chassis 1.12 DISTRIBUTED CHASSIS MANAGEMENT1.14 SWITCHING OPTIONS Installation in the SmartSwitch 6000 6C105 Chassis1.13 MANAGEMENT Standards Compatibility 1.16 LANVIEW DIAGNOSTIC LEDs1.15 STANDARDS COMPATIBILITY 1-8 Introduction2.1 SMARTTRUNK FEATURE Network Requirements2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 100BASE-TX Network2-2 Network Requirements Installation 3.2 INSTALLING OPTIONAL FLASH UPGRADE 3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS3.1 UNPACKING THE MODULE To install a module, refer to Figure 3-1 and proceed as follows 3-4 Installation Installing the Module into the Matrix E7 ChassisFigure 3-1 Installing a Module into the Matrix E7 Chassis Backplane Connectors Slot Number3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS 3-6 Installation Installing the Module into the 6C105 ChassisFigure 3-2 Installing a Module into the 6C105 Chassis 3387023.5 CONNECTING TO THE NETWORK 3.5.1 Connecting UTP Cables to the 6H302-48Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48 Group SelectButton 3.5.2 Connecting UTP Cables to the 6H303-48 Figure 3-4 Crossover Cable RJ45 PinoutsFigure 3-5 Straight-Through Cable RJ45 Pinouts Screw Hole Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48Screw ScrewScrew Hole3.6 COMPLETING THE INSTALLATION Completing the InstallationInstallation Page Troubleshooting 4.1 USING LANVIEWViewing Receive and Transmit Activity Using LANVIEW 4-2 TroubleshootingFigure 4-1 LANVIEW LEDs both modules Ensure chassis has adequate power Using LANVIEWPower off Solid. Resetting, normalTable 4-1 LANVIEW LEDs Continued Using LANVIEW4-4 Troubleshooting Color StateTable 4-2 Troubleshooting Checklist 4.2 TROUBLESHOOTING CHECKLISTTroubleshooting Checklist ProblemProblem Troubleshooting ChecklistTable 4-2 Troubleshooting Checklist Continued 4-6 Troubleshooting4.3 USING THE RESET BUTTON Figure 4-2 RESET Button both modulesPage Processors/Memory SpecificationsA.1 6H302-48 / 6H303-48 SPECIFICATIONS Physical Properties6H302-48 Environmental RequirementsInput/Output Ports 6H303-48Table A-2 COM Port Pin Assignments A.2 COM PORT PINOUT ASSIGNMENTSA.3 REGULATORY COMPLIANCE Table A-3 Compliance StandardsPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file B.3 FLASH UPGRADE B.3.1 Locating the FLASH ModuleB.3.2 Installing the FLASH Module Page Index NumericsIndex-2