Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H302-48 manual Completing The Installation, Completing the Installation

Models: 6H302-48

1 58

Download 58 pages 11 Kb

Page 37

Completing the Installation

b.Verify that the RJ21 connectors on the twisted pair segment have the proper pinouts and check the cable for continuity.

c.Check that the twisted pair connection meets the specifications in the Cabling Guide.

If a link is not established, contact Enterasys Networks. Refer to “Getting Help” in About This Guide for details.

5.Repeat steps 1 through 5, above, until all RJ21 connections are made.

3.6COMPLETING THE INSTALLATION

After installing the module and making the connections to the network, proceed as follows:

1.If the chassis is installed in a rack that has strain-relief brackets, secure the cables by running the cables along the strain-relief bracket and tying them to the bracket using cable ties.

2.The module is now ready to be configured through Local Management. Refer to the appropriate Local Management User’s Guide for information on how to access and use Local Management. For details on how to get manuals, refer to the “Related Documents” section in About This Guide.

Installation 3-11

Image 37

Enterasys Networks 6H302-48 manual Completing The Installation, Completing the Installation

Contents

6H302-48 6H302-48 and 6H303-48 Fast Ethernet User’s Guide6H303-48 FAST ENETPage Order Number 9033387-05 October Enterasys Networks, Inc 35 Industrial Way Rochester, NHINDUSTRY CANADA NOTICE FCC NOTICEVCCI NOTICE CLASS A ITE NOTICEBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTCAREFULLY READ THIS LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page ABOUT THIS GUIDE ContentsContents viii Contents INDEXFigures Figuresx Tables TablesAbout This Guide USING THIS GUIDEImportant Notices RELATED DOCUMENTS STRUCTURE OF THIS GUIDEMatrix E7 Overview and Setup Guide 6C105 SmartSwitch 6000 Overview and Setup GuideThe guide uses the following conventions DOCUMENT CONVENTIONSDocument Conventions About This GuideGETTING HELP Important Notice IntroductionFigure 1-1 6H302-48 and 6H303-48 Modules Group Select Switch Port Status LEDs Group Select LEDs Network Ports1-2 Introduction Network Ports1.2 RUNTIME IP ADDRESS DISCOVERY 1.1 CONNECTIVITY1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.4 SMARTTRUNK1.6 BROADCAST SUPPRESSION 1.5 REMOTE MONITORING RMON1.7 PORT/VLAN REDIRECT FUNCTIONS Remote Monitoring RMON1.9 FLOW CONTROL 1.8 TRAFFIC RATE LIMITINGInstallation in the Matrix E7 6C107 Chassis 1.10 GARP SWITCH OPERATION1.11 802.1 PORT PRIORITY 1.12 DISTRIBUTED CHASSIS MANAGEMENTInstallation in the SmartSwitch 6000 6C105 Chassis 1.14 SWITCHING OPTIONS1.13 MANAGEMENT 1.15 STANDARDS COMPATIBILITY 1.16 LANVIEW DIAGNOSTIC LEDsStandards Compatibility 1-8 IntroductionNetwork Requirements 2.1 SMARTTRUNK FEATURE2.2 10BASE-T NETWORK 100BASE-TX Network 2.3 100BASE-TX NETWORK2-2 Network Requirements Installation 3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS 3.2 INSTALLING OPTIONAL FLASH UPGRADE3.1 UNPACKING THE MODULE To install a module, refer to Figure 3-1 and proceed as follows Figure 3-1 Installing a Module into the Matrix E7 Chassis Installing the Module into the Matrix E7 Chassis3-4 Installation Backplane Connectors Slot Number3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS Figure 3-2 Installing a Module into the 6C105 Chassis Installing the Module into the 6C105 Chassis3-6 Installation 3387023.5.1 Connecting UTP Cables to the 6H302-48 3.5 CONNECTING TO THE NETWORKGroup Select Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48Button Figure 3-4 Crossover Cable RJ45 Pinouts 3.5.2 Connecting UTP Cables to the 6H303-48Figure 3-5 Straight-Through Cable RJ45 Pinouts Screw Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48Screw Hole ScrewScrew HoleCompleting the Installation 3.6 COMPLETING THE INSTALLATIONInstallation Page 4.1 USING LANVIEW TroubleshootingViewing Receive and Transmit Activity 4-2 Troubleshooting Using LANVIEWFigure 4-1 LANVIEW LEDs both modules Power off Using LANVIEWEnsure chassis has adequate power Solid. Resetting, normal4-4 Troubleshooting Using LANVIEWTable 4-1 LANVIEW LEDs Continued Color StateTroubleshooting Checklist 4.2 TROUBLESHOOTING CHECKLISTTable 4-2 Troubleshooting Checklist ProblemTable 4-2 Troubleshooting Checklist Continued Troubleshooting ChecklistProblem 4-6 TroubleshootingFigure 4-2 RESET Button both modules 4.3 USING THE RESET BUTTONPage A.1 6H302-48 / 6H303-48 SPECIFICATIONS SpecificationsProcessors/Memory Physical PropertiesInput/Output Ports Environmental Requirements6H302-48 6H303-48A.3 REGULATORY COMPLIANCE A.2 COM PORT PINOUT ASSIGNMENTSTable A-2 COM Port Pin Assignments Table A-3 Compliance StandardsPage B.1 REQUIRED TOOLS Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHES DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file B.3.1 Locating the FLASH Module B.3 FLASH UPGRADEB.3.2 Installing the FLASH Module Page Numerics IndexIndex-2