Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H302-48 Using LANVIEW, 1 LANVIEW LEDs, Color, State, Recommended Action, None

Models: 6H302-48

1 58

Download 58 pages 11 Kb

Page 41

			Using LANVIEW
Table 4-1 LANVIEW LEDs

LED	Color	State	Recommended Action

CPU	Off	Power off.	Ensure chassis has adequate power.

	Red	Blinking. Hardware	Contact Enterasys Networks for technical
		failure has occurred.	support.

		Solid. Resetting, normal	If the LED remains red for several minutes,
		power up reset.	contact Enterasys Networks for technical
			support.

	Amber	Blinking. Crippled.	Contact Enterasys Networks for technical
			support.

		Solid. Testing.	If the LED remains amber for more than
			several minutes, contact Enterasys
			Networks for technical support.

	Green	Solid. Functional.	None.

	Amber	Booting. Blinks amber	None.
	and	and green while booting.
	Green

RX	Off	No link.	None.
(Receive)		No activity or port in
		standby. Port enabled or
		disabled.

	Green	Solid. Link, port enabled,	None.
		no activity.

		Blinking. Link, port	None.
		disabled.

	Amber	Flashing. Link, port	None.
		enabled, activity.

	Red	Solid. Diagnostic failure.	Contact Enterasys Networks for
			assistance.

Troubleshooting 4-3

Image 41

Enterasys Networks 6H302-48 Using LANVIEW, 1 LANVIEW LEDs, Color, State, Recommended Action, Power off, Blinking. Hardware

Contents

6H302-48 6H302-48 and 6H303-48 Fast Ethernet User’s Guide6H303-48 FAST ENETPage Order Number 9033387-05 October Enterasys Networks, Inc 35 Industrial Way Rochester, NHINDUSTRY CANADA NOTICE FCC NOTICEVCCI NOTICE CLASS A ITE NOTICECAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page Contents ContentsABOUT THIS GUIDE viii Contents INDEXFigures Figuresx Tables TablesImportant Notices USING THIS GUIDEAbout This Guide RELATED DOCUMENTS STRUCTURE OF THIS GUIDEMatrix E7 Overview and Setup Guide 6C105 SmartSwitch 6000 Overview and Setup GuideThe guide uses the following conventions DOCUMENT CONVENTIONSDocument Conventions About This GuideGETTING HELP Important Notice IntroductionFigure 1-1 6H302-48 and 6H303-48 Modules Group Select Switch Port Status LEDs Group Select LEDs Network Ports1-2 Introduction Network Ports1.2 RUNTIME IP ADDRESS DISCOVERY 1.1 CONNECTIVITY1.3 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION 1.4 SMARTTRUNK1.6 BROADCAST SUPPRESSION 1.5 REMOTE MONITORING RMON1.7 PORT/VLAN REDIRECT FUNCTIONS Remote Monitoring RMON1.9 FLOW CONTROL 1.8 TRAFFIC RATE LIMITINGInstallation in the Matrix E7 6C107 Chassis 1.10 GARP SWITCH OPERATION1.11 802.1 PORT PRIORITY 1.12 DISTRIBUTED CHASSIS MANAGEMENT1.13 MANAGEMENT 1.14 SWITCHING OPTIONSInstallation in the SmartSwitch 6000 6C105 Chassis 1.15 STANDARDS COMPATIBILITY 1.16 LANVIEW DIAGNOSTIC LEDsStandards Compatibility 1-8 Introduction2.2 10BASE-T NETWORK 2.1 SMARTTRUNK FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.1 UNPACKING THE MODULE 3.2 INSTALLING OPTIONAL FLASH UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS To install a module, refer to Figure 3-1 and proceed as follows Figure 3-1 Installing a Module into the Matrix E7 Chassis Installing the Module into the Matrix E7 Chassis3-4 Installation Backplane Connectors Slot Number3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSIS Figure 3-2 Installing a Module into the 6C105 Chassis Installing the Module into the 6C105 Chassis3-6 Installation 3387023.5.1 Connecting UTP Cables to the 6H302-48 3.5 CONNECTING TO THE NETWORKButton Figure 3-3 Connecting a Twisted Pair Segment to the 6H302-48Group Select Figure 3-5 Straight-Through Cable RJ45 Pinouts 3.5.2 Connecting UTP Cables to the 6H303-48Figure 3-4 Crossover Cable RJ45 Pinouts Screw Figure 3-6 Connecting a Twisted Pair Segment to the 6H303-48Screw Hole ScrewScrew HoleInstallation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Page Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW Figure 4-1 LANVIEW LEDs both modules Using LANVIEW4-2 Troubleshooting Power off Using LANVIEWEnsure chassis has adequate power Solid. Resetting, normal4-4 Troubleshooting Using LANVIEWTable 4-1 LANVIEW LEDs Continued Color StateTroubleshooting Checklist 4.2 TROUBLESHOOTING CHECKLISTTable 4-2 Troubleshooting Checklist ProblemTable 4-2 Troubleshooting Checklist Continued Troubleshooting ChecklistProblem 4-6 TroubleshootingFigure 4-2 RESET Button both modules 4.3 USING THE RESET BUTTONPage A.1 6H302-48 / 6H303-48 SPECIFICATIONS SpecificationsProcessors/Memory Physical PropertiesInput/Output Ports Environmental Requirements6H302-48 6H303-48A.3 REGULATORY COMPLIANCE A.2 COM PORT PINOUT ASSIGNMENTSTable A-2 COM Port Pin Assignments Table A-3 Compliance StandardsPage B.1 REQUIRED TOOLS Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHES DO NOT attempt a Forced BootP unless a BootP server has been configured for the module. The BootP server references the location of a station acting as a Trivial File Transfer Protocol TFTP server containing the module image file B.3.1 Locating the FLASH Module B.3 FLASH UPGRADEB.3.2 Installing the FLASH Module Page Numerics IndexIndex-2