LCM Command Summary | Enterasys Networks ELS10-27TX specification

Enhancements to LCM Commands

Parameters that appear in all capital letters, for example workgroups [PORT-RANGE], indicate that you must enter a value for that parameter. If a string of parameters is displayed between braces, for example [name {addPORT-RANGE}], you must select one of the displayed options. For example, if you wanted to add ports to a workgroup, you would enter:

ELS10-27>workgroup alpha add 23, 24

For example, if you wanted to add a range of ports in a workgroup, you would enter:

ELS10-27>workgroup omega add 2-18

For a complete list of commands, refer to the SmartSTACK Ethernet ELS10- 27TX User Guide.

2.3 LCM COMMAND SUMMARY

This section contains a subset of LCM commands and syntax.

2.3.1 Subset of LCM Commands

The following is a subset of LCM commands and definitions.

Use ...	To ...


help or ?	display this menu

ipaddr [IPADDR [MASK]]	set or display IP addresses

port [? for syntax]	set or display port parameters

reboot [? for syntax]	reboot the unit after SECONDS

switch [? for syntax]	set or display switch parameters

vlan [? for syntax]	configure IEEE Vlans

workgroup [? for syntax]	set or display workgroups

2-2

Image 32

Enterasys Networks ELS10-27TX manual LCM Command Summary, Subset of LCM Commands

Contents

SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Configuring Vlans Using Snmp Vlan MIB Objects Xiii Configuring Workgroups Using LCM Configuring Workgroups Using SnmpWorkgroup MIB Objects Appendix a Virtual Lans Vlans Index About this Supplement Getting Help Your email address Document Conventions Related Documentation Document Title Part Number Using Vlans on the ELS10-27TX Product Overview Ieee 802.1Q Standard Vlan Access Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Hybrid Ports 802.1Q Mode 3 802.1Q Trunk Ports Preserving Priority Accessing Network Management Using VLANs Non-Preserving Priority Assigning Ports to a Vlan Switch ModeDefault Port Vlan ID Restricting VLANs 802.1Q Mode Enable Gvrp Virtual Workgroups will only operate in 802.1D mode Workgroups Default Gateway Installation and ManagementPage Overview LCM Conventions LCM Command Summary Subset of LCM Commands LCM Command Syntax Basic LCM Commands HelpErase Exit or Logout LCM Commands Enable Command Address Limit Route Command Port Command Port Command Enhancements to LCM Commands Switch Command Trap Control Command Vlan Command ELS10-27vlan add 5-9 bluePage Configuring Vlans Using Snmp Overview Config Table Modifying a Vlan Modifying, Creating and Deleting VLANsStep Action Creating a Vlan Deleting a Vlan Config Egress List Modifying a Config Egress List Entry Filter Gvrp Table Modifying, Creating or Deleting a Filter Gvrp Table Entry Creating a Filter Deleting a Filter Deleting a Static MAC Entry Static MAC EntryCreating a Static MAC Entry Bridge Configuration Vlan Version Number Operating Mode VlanOperatingMode Reset VlanReset Gvrp Enable VlanGVRPEnable Syntax Octet String Size Access List VlanAccessList Vlan VlanConfigVlan VlanConfigEntry Configuration EntriesEntry VlanConfigEntry Index VlanConfigIndex VID VlanConfigVID Ports VlanConfigPorts IP VlanConfigIP IP Mask VlanConfigIPMask Name VlanConfigName Status VlanConfigStatus Establish VlanConfigEstablish Active VlanNumActiveEntries Static Configured VlanNumConfiguredEntriesDevice Entries Configuration Table VlanConfigTable Maximum Number VlanMaxNumEntries Egress Table Egress Table VlanConfigEgressTable Egress Entry VlanConfigEgressEntry VlanConfigEgressEntry Index VlanEgressIndex VID VlanEgressVID List VlanEgressList Status VlanEgressStatus Entry VlanFilterGVRPEntry Filter GvrpGvrp VlanFilterGVRPTable VlanFilterGVRPIndex VlanFilterGVRPEntry VID VlanFilterGVRPVID List VlanFilterGVRPList Status VlanFilterGVRPStatus EstablishVID VlanFilterGVRPEstablishVID Entry VlanStaticEntry Static MAC Address EntriesTable VlanStaticTable VID VlanStaticVID VlanStaticEntry MAC VlanStaticMAC Port VlanStaticPort Establish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Configuration Examples Workgroup Default Workgroup Superset LCM Workgroup Commands Workgroups are only valid in 802.1D mode ELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Next Number WorkGroupNextNumber Workgroups Using SnmpChapter Workgroup MIB Objects Overview Current Count WorkGroupCurrentCount MAX Count WorkGroupMaxCount Table WorkGroupTable Entry WorkGroupEntry Number WorkGroupNumber Name WorkGroupName Ports WorkGroupPorts Type WorkGroupType Appendix a Virtual Lans Vlans Vlans and Frame Tagging Vlan Vlan Y ELS10-27TX Vlan Configuration Vlan ID Vlan Egress Vlan Access PortsPorts in Vlan Figure A-2. Vlan Access Ports Index Numerics Snmp Index