Static MAC Entry | Enterasys Networks ELS10-27TX manual

Configuring VLANs Using SNMP

3.5 THE STATIC MAC ENTRY

Only three local variables are accessible, the VLAN ID; the MAC address, and the port to associate with this entry. MAC addresses added via this mechanism are not saved after a reboot, and will not age.

For a list of Static MAC variables, refer to Chapter 3, Configuring VLANs Using SNMP.

3.5.1 Creating a Static MAC Entry

To create a new entry, proceed as follows:

Step	Action


1	Set the VLAN ID.

2	Set the MAC address.

3	Set the port.

4	Set the establish variable to Create.

If the VLAN ID is not valid or the entry already exists, the command will be aborted. If it does not exist, it will be added.

3.5.2 Deleting a Static MAC Entry

To delete an entry, proceed as follows:

Step	Action

1Set the VLAN ID.

2Set the MAC address.

3Set the establish variable to delete.

If the entry already exists, it will be deleted. If it does not exist, the command will be aborted.

3-8

Image 50

Enterasys Networks ELS10-27TX manual Creating a Static MAC Entry, Deleting a Static MAC Entry

Contents

SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Configuring Vlans Using Snmp Vlan MIB Objects Xiii Workgroup MIB Objects Configuring Workgroups Using LCMConfiguring Workgroups Using Snmp Appendix a Virtual Lans Vlans Index About this Supplement Getting Help Your email address Document Conventions Related Documentation Document Title Part Number Using Vlans on the ELS10-27TX Product Overview Ieee 802.1Q Standard Vlan Access Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Hybrid Ports 802.1Q Mode 3 802.1Q Trunk Ports Preserving Priority Accessing Network Management Using VLANs Non-Preserving Priority Assigning Ports to a Vlan Switch ModeDefault Port Vlan ID Restricting VLANs 802.1Q Mode Enable Gvrp Virtual Workgroups will only operate in 802.1D mode Workgroups Default Gateway Installation and ManagementPage Overview LCM Conventions LCM Command Summary Subset of LCM Commands LCM Command Syntax Erase Basic LCM CommandsHelp Exit or Logout LCM Commands Enable Command Address Limit Route Command Port Command Port Command Enhancements to LCM Commands Switch Command Trap Control Command Vlan Command ELS10-27vlan add 5-9 bluePage Configuring Vlans Using Snmp Overview Config Table Modifying a Vlan Modifying, Creating and Deleting VLANsStep Action Creating a Vlan Deleting a Vlan Config Egress List Modifying a Config Egress List Entry Filter Gvrp Table Modifying, Creating or Deleting a Filter Gvrp Table Entry Creating a Filter Deleting a Filter Deleting a Static MAC Entry Static MAC EntryCreating a Static MAC Entry Bridge Configuration Vlan Version Number Operating Mode VlanOperatingMode Reset VlanReset Gvrp Enable VlanGVRPEnable Syntax Octet String Size Access List VlanAccessList Vlan VlanConfigVlan VlanConfigEntry Configuration EntriesEntry VlanConfigEntry Index VlanConfigIndex VID VlanConfigVID Ports VlanConfigPorts IP VlanConfigIP IP Mask VlanConfigIPMask Name VlanConfigName Status VlanConfigStatus Establish VlanConfigEstablish Active VlanNumActiveEntries Static Configured VlanNumConfiguredEntriesDevice Entries Configuration Table VlanConfigTable Maximum Number VlanMaxNumEntries Egress Table Egress Table VlanConfigEgressTable Egress Entry VlanConfigEgressEntry VlanConfigEgressEntry Index VlanEgressIndex VID VlanEgressVID List VlanEgressList Status VlanEgressStatus Entry VlanFilterGVRPEntry Filter GvrpGvrp VlanFilterGVRPTable VlanFilterGVRPIndex VlanFilterGVRPEntry VID VlanFilterGVRPVID List VlanFilterGVRPList Status VlanFilterGVRPStatus EstablishVID VlanFilterGVRPEstablishVID Entry VlanStaticEntry Static MAC Address EntriesTable VlanStaticTable VID VlanStaticVID VlanStaticEntry MAC VlanStaticMAC Port VlanStaticPort Establish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Configuration Examples Workgroup Default Workgroup Superset LCM Workgroup Commands Workgroups are only valid in 802.1D mode ELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Next Number WorkGroupNextNumber Workgroups Using SnmpChapter Workgroup MIB Objects Overview Current Count WorkGroupCurrentCount MAX Count WorkGroupMaxCount Table WorkGroupTable Entry WorkGroupEntry Number WorkGroupNumber Name WorkGroupName Ports WorkGroupPorts Type WorkGroupType Appendix a Virtual Lans Vlans Vlans and Frame Tagging Vlan Vlan Y ELS10-27TX Vlan Configuration Vlan ID Vlan Egress Vlan Access PortsPorts in Vlan Figure A-2. Vlan Access Ports Index Numerics Snmp Index