Port Command | Enterasys Networks ELS10-27TX specification

Enhancements to LCM Commands

2.5.3 Port Command

The Port command allows you to configure the port(s) on the unit in regards to speed, duplex mode, broadcast storm protection values, GVRP, access ports, flow control, and the default VLAN ID used on each port. If the default VLAN ID for a port was configured, the port will not automatically become a member of that VLAN.

Naming a VLAN. A VLAN is not named using the port command. The VLAN must be created first using the VLAN command and this port made a member. Refer to the VLAN command to name a VLAN described later in this chapter. Likewise, if the default VLAN ID is changed, the port is not removed from the old VLAN. You must use the VLAN command to remove the port from the VLAN.

The VLAN sub-command is used to configure the port VLAN ID for a port. Three of the VLAN sub-commands relate to configuring VLANs such as, VLAN, GVRP, and Access.

VLAN Sub-Command.The VLAN sub-command is used to configure the default VLAN ID for a port.

GVRP Sub-Command.The GVRP sub-command allows you to specify that GVRP is enabled on all specified ports. If enabled, GVRP messages are received on these ports and GVRP messages are propagated to these ports.

Access Sub-Command.The access sub-command allows you to specify which ports are treated as access ports.

The Port Command

port [PORT-RANGE [speed {auto 10[Mbps] 100[Mbps]}] [duplex [{auto full[-duplex] half[-duplex]}]] [storm THRESHOLD TIME-INTERVAL] [vlan {name VLAN-ID}]

[802.3x [flow control] {on off}] [GVRP {On off}]

[access {add del[ete]}]

2-7

Image 37

Enterasys Networks ELS10-27TX manual Port Command

Contents

SmartSTACK Ethernet ELS10-27TX Supplement Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Page Declaration of Conformity Contents Vlan MIB Objects Configuring Vlans Using Snmp Xiii Configuring Workgroups Using Snmp Configuring Workgroups Using LCMWorkgroup MIB Objects Appendix a Virtual Lans Vlans Index About this Supplement Your email address Getting Help Document Conventions Document Title Part Number Related Documentation Product Overview Using Vlans on the ELS10-27TX Ieee 802.1Q Standard Vlan Hybrid Ports 802.1Q Mode 802.1Q Mode on ELS10-27TXVlan Access Ports 802.1Q Mode Preserving Priority 3 802.1Q Trunk Ports Non-Preserving Priority Accessing Network Management Using VLANs Default Port Vlan ID Switch ModeAssigning Ports to a Vlan Enable Gvrp Restricting VLANs 802.1Q Mode Workgroups Virtual Workgroups will only operate in 802.1D mode Installation and Management Default GatewayPage LCM Conventions Overview Subset of LCM Commands LCM Command Summary LCM Command Syntax Help Basic LCM CommandsErase Exit or Logout Enable Command Address Limit LCM Commands Route Command Port Command Port Command Enhancements to LCM Commands Switch Command Trap Control Command ELS10-27vlan add 5-9 blue Vlan CommandPage Config Table Configuring Vlans Using Snmp Overview Step Action Modifying, Creating and Deleting VLANsModifying a Vlan Deleting a Vlan Creating a Vlan Config Egress List Modifying a Config Egress List Entry Modifying, Creating or Deleting a Filter Gvrp Table Entry Filter Gvrp Table Deleting a Filter Creating a Filter Creating a Static MAC Entry Static MAC EntryDeleting a Static MAC Entry Vlan Version Number Bridge Configuration Reset VlanReset Operating Mode VlanOperatingMode Syntax Octet String Size Gvrp Enable VlanGVRPEnable Vlan VlanConfigVlan Access List VlanAccessList Entry VlanConfigEntry Configuration EntriesVlanConfigEntry VID VlanConfigVID Index VlanConfigIndex IP VlanConfigIP Ports VlanConfigPorts Name VlanConfigName IP Mask VlanConfigIPMask Establish VlanConfigEstablish Status VlanConfigStatus Device Entries Static Configured VlanNumConfiguredEntriesActive VlanNumActiveEntries Maximum Number VlanMaxNumEntries Configuration Table VlanConfigTable Egress Entry VlanConfigEgressEntry Egress Table Egress Table VlanConfigEgressTable Index VlanEgressIndex VlanConfigEgressEntry List VlanEgressList VID VlanEgressVID Status VlanEgressStatus Gvrp VlanFilterGVRPTable Filter GvrpEntry VlanFilterGVRPEntry VlanFilterGVRPEntry VlanFilterGVRPIndex List VlanFilterGVRPList VID VlanFilterGVRPVID EstablishVID VlanFilterGVRPEstablishVID Status VlanFilterGVRPStatus Table VlanStaticTable Static MAC Address EntriesEntry VlanStaticEntry VlanStaticEntry VID VlanStaticVID Port VlanStaticPort MAC VlanStaticMAC Establish VlanStaticEstablish Page Chapter Configuring Workgroups Using LCM Overview Workgroup Default Workgroup Configuration Examples Workgroup Superset Workgroups are only valid in 802.1D mode LCM Workgroup Commands ELS10-27workgroup omega Page Chapter Configuring Workgroups Using Snmp Overview Workgroup Configuration Procedures Configuring Workgroups Using Snmp Page Chapter Workgroup MIB Objects Overview Workgroups Using SnmpNext Number WorkGroupNextNumber MAX Count WorkGroupMaxCount Current Count WorkGroupCurrentCount Table WorkGroupTable Entry WorkGroupEntry Name WorkGroupName Number WorkGroupNumber Type WorkGroupType Ports WorkGroupPorts Vlan Vlan Y Appendix a Virtual Lans Vlans Vlans and Frame Tagging Vlan ID ELS10-27TX Vlan Configuration Ports in Vlan Vlan Access PortsVlan Egress Figure A-2. Vlan Access Ports Numerics Index Snmp Index