Manuals / Brands / Computer Equipment / All in One Printer / Epson / Computer Equipment / All in One Printer

Epson 810, 820, 830 Table 3-19.Check point for the poor printing quality

1 165

Download 165 pages, 13.36 Mb

EPSON Stylus PHOTO 810/820/830

Revision B

Table 3-19. Check point for the poor printing quality

Occurrence

Detailed phenomenon

Defective

Check point

Remedy

timing

unit/part name

CR position

1. Check if there is any foreign material around the seal

1. Remove the foreign material around the seal

[Phenomenon 1]

rubber parts on the Cap unit.

rubber parts carefully.

In the CL sequence, the Pump unit seems

Seal rubber portion

* The left figure is the cap for Stylus C20.

to work correctly. But, the ink is not

The function of the Cap unit is the same

ejected to the Waste drain ink pad at all.

although the cap size is different between

Moreover, any ink is not absorbed from

Stylus C20 and Stylus Photo 810/820.

the Printhead to the cap.

[Phenomenon 2]

2. Check if any damage is observed around the seal rubber

In the CL sequence, the ink is ejected to

parts on the Cap unit.

2. Replace the Printer mechanism with new one.

3. Check if the Compression spring is assembled in the Cap

the Waste drain ink pad (this means the

Pump unit & the Cap unit works

unit correctly.

3. Replace the Printer mechanism with new one.

correctly). But, the dot missing is not

solved at the specific nozzles even if the

several CLs are performed.

[Phenomenon 3]

Operation

Compression spring

In the CL sequence, the ink is ejected to

Cap unit

4. Check if the Pump tube is connected to the bottom of the

-

the Waste drain ink pad (this means the

Pump unit & the Cap unit works

Cap unit correctly

correctly). But, the wiping operation is

4. Replace the Printer mechanism with new one.

not performed correctly and the colors

are mixed.

[Phenomenon 4]

In the CL sequence, the ink is ejected to

Pump tube

connection point

the Waste drain ink pad. But, the dot

5. Check if the Extension spring 0.523 comes off from the

missing occurs on the several nozzle in

the printing.

Slider cap.

6. Check if the Extension spring 0.383 comes off from the

5. Reassemble the Extension spring 0.523

[Phenomenon 5]

Slider lock lever.

correctly.

6. Reassemble the Extension spring 0.383

In the CL sequence, the ink is ejected to

Exp. spring 0.523

the Waste drain ink pad. But, the missing

correctly.

point (dot missing nozzle) is changed in

Exp. spring 0.383

every CL operation.

Troubleshooting

Unit Level Troubleshooting

82

Contents

EPSON Stylus PHOTO 810/820/830 Notice PRECAUTIONS About This Manual Revision Status PRODUCT DESCRIPTION Operating Principles Troubleshooting Disassembly and Assembly Adjustment Maintenance Appendix PRODUCT DESCRIPTION 1.1 FEATURES 1.2 SPECIFICATIONS Plain Paper 1.2.4.2 Envelope 1.2.4.3 Exclusive paper Page Cut Sheet 1.2.5.2 Envelopes 1.2.6.1 Black Ink Cartridge 1.2.6.2 Color Ink Cartridge [UPS Version] (Stylus Photo 820/830) 1.2.8 Environmental Condition Humidity (%) Temperature (°C) Figure 1-7.Temperature/Humidity range 1.2.9 Reliability 1.2.10 Safety Approvals [220∼ 240V Version] (Stylus Photo 810/820) 1.2.11 Acoustic Noise 1.2.12 CE Marking 1.3 INTERFACE Table 1-11.Typical time of tack Table 1-13.Connector pin assignment and signals Table 1-12.Signal level: TTL compatible (IEEE-1284level 1 device) Table 1-13.Connector pin assignment and signals (continued) NOTE: 1.3.2 Parallel Interface (Reserve Channel) Table 1-14.Connector pin assignment and signals Table 1-14.Connector pin assignment and signals (continued) „ Stylus Photo 810/820 „Stylus Photo 820/830 1.3.3 USB Interface Table 1-15.Connector pin assignment and signals Pin #2 Pin #1 Pin #3 Page 1.4 PANEL CONTROL Power Error reset Ink cartridge exchange 1.4.3 Printer Condition and Panel Status Table 1-18.Printer condition and LED status 1.4.4 Error Status †Ink end error †Paper out error 1.4.5 Printer Initialization OPERATING PRINCIPLES 2.1 Overview 2.1.2 Printhead Figure 2-2.Nozzle layout for Stylus Photo 810/ 820/830 Figure 2-3.Printhead sectional drawing 2.1.2.1 Printing Process 2.1.2.2 Printing Method 2.1.3 Carriage Mechanism Figure 2-5.Carriage mechanism (Top view) Table 2-1.Carriage motor specification Figure 2-6.CR home position detection 2.1.4 Paper Loading/Feeding Mechanism Table 2-2.PF motor specifications Table 2-3.ASF unit function & PF motor rotational direction Figure 2-7.Paper loading/feeding mechanism 2.1.4.1 Paper Loading Mechanism (ASF unit) Figure 2-8.ASF paper loading sequence (Step 1, 2) Figure 2-9.ASF paper loading sequence (Step 3, 4) 2.1.4.2 Paper Feeding Mechanism 2.1.5.1 Capping Mechanism Capping position (CR home position) Wiper setting position Wiping position Released position (Bottom position) Figure 2-12.Wiper mechanism 2.1.5.2 Pump unit mechanism 2.1.6 Ink Sequence Page 2.2 Electrical Circuit Operating Principles 2.2.1.1 C417 PSB/PSE board Page 2.2.1.2 C482 PSH board Page 2.2.2C417/C418 Main/Main-BBoard 2.2.2.1 Main Elements 2.2.2.2 Printhead Driver Circuit 2.2.2.3 PF Motor (PF/ PUMP/ ASF Motor) Driver Circuit 2.2.2.4 CR Motor Driver Circuit 2.2.2.5 Reset Circuit 2.2.2.6 EEPROM Control Circuit 2.2.2.7 Sensor Circuit 2.2.3 C483/C484 MAIN-BBoard Table 2-9.3.3VDC drive chips & 5VDC drive chips Figure 2-25.Block diagram for the C483/C484 Main-Bboard 2.2.3.1 Main Elements 2.2.3.2 Printhead Driver Circuit 2.2.3.3 PF/CR Motor Driver Circuit 2.2.3.4 Reset Regulator Circuit 2.2.3.5 EEPROM Control Circuit 2.2.3.6 Sensor Circuit TROUBLESHOOTING 3.1 Overview 3.2Troubleshooting with LED Error Indications and Status Monitor 3 Message Page Page Stylus Photo Revision B Page 3.3 Unit Level Troubleshooting Table 3-5.Check point for the fatal error according to each phenomenon EPSON Stylus PHOTO 810/820/830 Table 3-6.Paper jam error condition and possible cause Table 3-7.Check point for the paper jam error according to each phenomenon Page Page Table 3-7.Check point for the paper jam error according to each phenomenon Table 3-8.Paper out error condition and possible cause Table 3-9.Check point for the paper out error according to each phenomenon Table 3-9.Check point for the paper out error according to each phenomenon Page Table 3-10.Communication error condition and possible cause Table 3-11.Check point for the communication error according to each phenomenon Page Table 3-14.Multiple papers are always loaded without LEDs and STM3 Table 3-16.Abnormal noise Table 3-17.Check point for the abnormal noise Table 3-18.Poor printing quality Page Table 3-19.Check point for the poor printing quality Page Page Page Page DISASSEMBLY AND ASSEMBLY 4.1 Overview 4.1.3Screws 4.1.4 Work Completion Check Table 4-3.Work Completion Check 4.2Difference on Printer Machanism between SP810/820 and SP820/830 †If other I/C is installed on Stylus Photo 810/820/830, the printer detects ink end error 4.2.1 Caution in reassembling to ink leakage problem 4.3 Disassembly 4.3.1 Upper housing removal Figure 4-4.Edge guide setting position for the Lower housing removal † Make sure that the Edge guide is in the cutout portion of the Upper housing Figure 4-5.Hooks position of the Upper housing Figure 4-6.Protrusion position of the Upper housing †Do not damage the protrusion by the precision screwdriver (-) †When assembling the Upper housing to the printer 4.3.2 Printhead removal Figure 4-7.Head FFC holder removal Figure 4-8.Printhead removal Figure 4-9.Printhead installation position (pin & the grounding plate) Figure 4-10.Head FFC setting position 4.3.3 CR unit removal Figure 4-11.CR timing belt removal Figure 4-12.Compression spring 19.6 removal Figure 4-13.CR guide shaft rod spring release † In this step, you cannot remove the left CR guide shaft rod spring Figure 4-14.CR unit removal †Remove the CR guide shaft while holding the CR unit by hand. If Paper guide front, which causes the dot missing problem † Unlike the previous printer (Stylus COLOR 680), the oil pad is not built in the CR unit Figure 4-16.Grounding plate assembling position Figure 4-17.CR guide shaft rod spring setting procedure 4.3.4 CR motor removal 2)1st dot position adjustment †When assembling the CR motor to the Main frame Figure 4-18.CR motor assembling Tightening torque for the CR motor hexagon nut is as follows 4.3.5 ASF unit removal Figure 4-19.Screw position for removing the ASF unit Figure 4-20.Compression spring 2.50 and the Hopper removal Figure 4-21.Torsion spring 29.1 setting position Figure 4-23.ASF fixing screws fastening order Figure 4-22.Hopper pad and LD pad setting position 4.3.6 PSB/PSE unit removal Figure 4-24.PSB/PSE unit removal Figure 4-25.Upper power supply board shield plate removal Figure 4-26.Power supply board removal „Make sure to install the Power supply board correctly Figure 4-27.Tightening procedure for the PSB/PSE board •C.B.(O). SCREW, 4x5, F/Zg (1 pcs) : 11 ± 1 kgf.cm •C.B.S. SCREW, 3x6, F/Zn (2 pcs) : 6 ± 1 kgf.cm •C.B.S-TITESCREW, 3x6, F/Zn (1 pcs) : 6 ± 1 kgf.cm Figure 4-29.Power supply board shield plate setting position 4.3.7 Holder shaft unit removal Figure 4-30.Head FFC removal Figure 4-31.LD roller shaft holder removal Figure 4-32.LD roller with Clutch mechanism removal Figure 4-33.HP/PE sensor removal †When assembling the HP/PE detection lever to the LD roller shaft holder Figure 4-34.Torsion spring 0.22 for each detection lever „Make sure that the HP/PE detection lever moves smoothly †When assembling the HP/PE sensor to the LD roller shaft holder Figure 4-36.Clutch assembling Figure 4-37.Spur Gear 35.2 and Combination gear Figure 4-38.LD roller shaft holder assembling procedure (1) Figure 4-39.LD roller shaft holder assembling procedure (2) 4.3.8 Circuit board removal Figure 4-40.SW button removal Figure 4-41.Circuit board removal Figure 4-42.Hooks on the M/B mounting plate Figure 4-43.Main board shield plate removal Figure 4-44.Circuit board assembling Page 4.3.9 Waste drain ink pad (under the ASF unit) removal Figure 4-45.Waste drain ink pad setting position Figure 4-46.Ink tube setting position 4.3.10 Lower housing removal (home position side) Figure 4-48.Paper eject roller sliding procedure †Do not damage the Spur gear 60 when sliding the Paper eject roller to the left side Figure 4-49.Printer mechanism removal (1) Figure 4-50.Cap unit removal Figure 4-51.Cap unit setting position † Do not touch the sealing rubber portion and the cleaner head of the Cap unit when inserting the Cap unit to the Main frame Figure 4-52.Printer mechanism removal (2) Figure 4-53.Printer mechanism removal †When lifting the Printer mechanism from the Lower housing, be †When assembling the Printer mechanism to the Lower housing Figure 4-54.Reinforcing plate setting position Figure 4-56.Printer mechanism assembling(2) Figure 4-58.Bush position of the Paper eject roller Figure 4-57.Ink tube setting position Page 4.3.12Ink system unit removal (Cap unit, Pump unit & Waste drain ink pad) Figure 4-59.Cap unit removal Figure 4-60.Ink system unit removal position Figure 4-61.Ink system removal procedure †When removing the Ink system unit, be careful so that the gears do not come off from each shaft of the Ink system frame † When getting out of the ink tube, check the marking on the ink tube in advance Figure 4-62.Marking position on the Ink tube Figure 4-64.Gear engagement on the Ink system frame Figure 4-65.Compression spring 1.764 setting position 4.3.13 PF roller unit removal Figure 4-66.Paper guide removal procedure (1) † When removing the Paper guide upper/left, avoid to damage the figure below Figure 4-67.Paper guide removal procedure (2) Figure 4-71.Paper guide assembling (2) Figure 4-70.Paper guide assembling (1) Figure 4-72.Paper guide assembling (3) 4.3.14 PF motor removal Figure 4-73.PF motor removal † When removing the PF motor, do not damage the pinion gear of the PF motor with the Main frame †When assembling the PF motor to the Main frame ADJUSTMENT 5.1 Overview Page MAINTENANCE 6.1 Overview Figure 6-1.Status monitor 3 indication Figure 6-3.Maintenance error indication in STM3 Figure 6-2.Head cleaning function in the printer driver utility 6.1.3 Lubrication „Never use oil or grease other than those specified in this „ Never apply larger amount of grease than specified in this manual Table 6-1.Specified lubricants Table 6-2.Lubrication point 30 mm Figure 6-4.Lubrication point Figure 6-6.Lubrication point 3 (1) 20 mm Figure 6-5.Lubrication point Page APPENDIX 7.1 Connector Summary Table 7-4.CN4 - HP/PE Sensor (Stylus Photo 810/820) Table 7-5.CN4 - HP/PE sensor (Stylus Photo 820/830) Table 7-6.CN7 - PF Motor (Stylus Photo 810/820/830) Table 7-7.CN8 - Printhead (Stylus Photo 810/820/830) Table 7-8.CN9 - Printhead (Stylus Photo 810/820/830) Table 7-9.CN12 - CR Motor (Stylus Photo 810/820/830) 7.1.2 EEPROM Address Map Table 7-10.EEPROM Address Map (Stylus Photo 810/820) Table 7-10.EEPROM Address Map (Stylus Photo 810/820) (continued) Name mode Customer name Parallel Table 7-11.EEPROM Address Map (continued) Table 7-12.EEPROM address map (Stylus Photo 820/830) Page Table 7-13.EEPROM Address Map (continued) Page 7.2 Component Layout Page 7.3 Exploded Diagram Page Page Page Page Page Page Page Page Page Page 7.4 Parts List Table 7-14.Stylus PHOTO 810/820 Parts List <Stylus Photo 820/830 Table 7-15.Stylus Photo 8120/830 parts list Table 7-15.Stylus Photo 8120/830 parts list 7.5 Electrical Circuits