Manuals / EverFocus / TV and Video / DVR

EverFocus EMV400 user manual Video Inputs/Outputs Installation, 1.11ALARM CONTACTS INSTALLATION

Models: EMV400

1 129

Download 129 pages 3.46 Kb

Page 25

1.9 VIDEO INPUTS/OUTPUTS INSTALLATION

Cameras and CCTV monitors must use copper center conductor/copper braid 75 Ohm video cable (e.g. RG-59, RG-6, RG-11) with BNC connectors.

To avoid impedance mismatch and undesired loss/reflections, 50 Ohm coax cable (e.g. RG-58), or 75 ohm foil shield antenna cable and other types of coaxial cable are not compatible.

All connected video sources must provide a 1 Vpp NTSC or PAL standard video signal.

When converting other transmission types (twisted pair, fiber optics, radio) for the video inputs, be sure to verify accurate receiver calibration and signal levels.

ATTENTION: In order for the system to auto-detect the appropriate video format (NTSC or PAL), make sure that there is a video signal on video input 1 upon power-up.

1.10 AUDIO INSTALLATION

This DVR provides 4 line level audio inputs and 1 line level audio output.

ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone amplifier is required). The audio output requires an amplifier to drive a speaker or headphones.

The installation must be connected with audio coax cable and RCA plugs.

AUDIO RECORDING FUNCTIONALITY:

Audio recording is activated / deactivated in the Camera Menu for Camera #1~4 respectively. Please check and always comply with local laws and regulations when using audio recording.

The audio channel is always recorded together with video and is independent of the image recording rate. Though the audio record control is done in the Camera #1~4 screen, there is no specific camera allocation.

1.11ALARM CONTACTS INSTALLATION

The alarm inputs can be used to start recording or for recording rate adjustment. In addition, alarm reactions such as camera display on the monitor, buzzer, e-mail and network alarm are available. The alarm output relay can be switched if required. Alarm input response actions can be controlled according to a flexible schedule.

17

Image 25

EverFocus EMV400 user manual Video Inputs/Outputs Installation, 1.11ALARM CONTACTS INSTALLATION, Audio Installation

Contents

User Manual EMV400 DVRRelease Date Oct EMV400 DVR Instruction Manual Cleaning Safety Precautions Read Instructions  Retain Instructions Attachments  Power Cord Protection Water and Moisture  ServicingWEEE DVR CONFIGURATION CONFIGURATIONMOUSE OPERATION TABLE OF CONTENTS6 REMOTE OPERATION FROM BROWSER NETWORKING OVERVIEWInstalling ActiveX controls BROWSER SECURITY SETTING6.2.1 6.2.21 PRODUCT OVERVIEW 1.1 FEATURESChapter  Temperature -20ºC ~ 55ºC Operating, -20ºC ~ 85ºC Non-Operating 1.2 PACKAGE CONTENTSScrews x 1 pack Antenna x 1 set IR Remote Control x Battery x Camera Power cable x Video & Audio cable x Alarm cable xEMV400 - 4CH Mobile DVR 1.3 SPECIFICATIONSRequires real time network connectivity though cellular or WiFi Multiple email notifications in response to alarms and eventsservice Embedded 3-axis G Sensor data recorded alarm if separate user1.4 FRONT PANEL Record This LED ON indicates Record active Power This LED ON indicates Power onFigure 1-2 Rear Panel 1.5 REAR PANEL4 GPS Data Input Connect this connector to GPS receiver via GPS cable Please refer to the following diagrams for the system connections 1.6 SYSTEM CONNECTIONPOWER 1.7 REAR PANEL CONNECTORALARM IN CAM POWER2 CAM POWER112V OUT 12V OUTInterface Interface 1.8 INSTALLATION OF EMV400Suspend  Show all the possible ways to mount the DVR Use the two Z-brackets supplied to mount it in any ways shown Equipment Required Quick Installation Guide  Unpack EverythingPage Trunk Users are suggested to use “suspend” for mounting option  Installing the Cameras and Monitor 1.11ALARM CONTACTS INSTALLATION 1.9 VIDEO INPUTS/OUTPUTS INSTALLATION1.10 AUDIO INSTALLATION 1.11.1 Alarm Input Contacts 1.12 USB-Mouse installation1.11.2 Alarm Output Relay 1.13 NETWORK CONNECTION1.13.2 Network Connection through Patch Cable 1.13.1 Direct PC Connection through Crossover Network CableFigure 1-3 Direct PC Connection Figure 1-4 Network Connection through Patch CablePinout of straight patch cable 1.14 FINAL INSTALL PROCESS2 MOUSE OPERATION 2.1.1 How to select a channel2.1 GENERAL USB MOUSE OPERATION 2.1.2 OSD Root Menu2.1.3 Field Input Options 3.1 CONFIGURATION OF DVR 3 CONFIGURATION3.2 LOGIN ChapterFigure 3-3 On-screen Configuration 3.3 On Screen Configuration MenuFigure 3-2 On-screen Keyboard Playback Bar 3.4.1 Time Search 3.4 SEARCH3.4.2 G Sensor Search Figure 3-6 Search Menu - GPS Search 3.4.3 GPS Speed SearchFigure 3-7 Search Menu - GPS Bordering Search button to return to the previous level of menuFigure 3-8 Search Menu - Event Search 3.4.4 Event SearchPlay Playback selected item Delete Delete selected item Prev Page Go to previous page Next Page Go to next pageClick button to return to the previous level of menu Click button to enter G Sensor search menuFigure 3-10 Archive Menu 3.5 ARCHIVE USB4.1 Configuration Menu 4 DVR CONFIGURATIONChapter Figure 4-2 Configuration Menu 4.2.1 Normal 4.2 CAMERA SETTINGFigure 4-5 Camera Settings-Video Loss 4.2.2 Video AdjustSpeed 4.2.3 Alarm4.3.1 Record 4.3 RECORD SETTING4.4.1 Alarm-Alarm Settings 4.4 ALARM/GPSEnable Check box to enable response to that alarm trigger Alarm Select the alarm input trigger connection number from 1 toTransparent Alarm output remains as long as the alarm input is active Buzzer Check this box to enable the buzzer when an alarm occursFigure 4-10 Alarm - Event Settings 4.4.2 Alarm-Event SettingsFigure 4-11 Alarm - Event - Fan Failure Fan FailureFigure 4-12 Alarm - Event - HD Temperature HD TemperatureFigure 4-13 Alarm - Event - HD Failure HD FailureFigure 4-14 Alarm - Event - HD Full HD FullFigure 4-15 Alarm - Event - HD Off HD OffFigure 4-16 Alarm - Event - Power Loss Power LossFigure 4-17 Alarm - Event - Network Loss Network LossFigure 4-18 Alarm - Event - GPS Loss GPS LossFigure 4-19 Alarm - Video Loss 4.4.3 Alarm - Video LossPage Figure 4-20 Alarm - G-Sensor 4.4.4 Alarm-G-Sensor SettingsFigure 4-21 Alarm - GPS Speed 4.4.5 Alarm-GPS SpeedFigure 4-22 Alarm - GPS Event Action 4.4.6 Alarm-GPS Event ActionFigure 4-23 Alarm - GPS Fencing 4.4.7 Alarm-GPS Fencing4.5.1 Date/Time Settings 4.5 Date/Time SettingFigure 4-25 Date/Time Settings-Daylight Saving 4.5.2 Daylight Saving4.6.1 Title 4.6 Display4.6.2 Monitor On Screen Display Main Monitor Click button to set up Layout parameters 4.6.3 Layout4 Up Type Layout type for the display switch Main MonitorFigure 4-29 Display-Sequence 4.6.4 Sequence4.7.1 LAN Settings 4.7 NETWORK SETTINGNetwork Type Well Known Ports 0 thru Registered Ports 1024 thru The default port for the EMV400 isDynamic and/or Private Ports 49152 thru Click button to start LAN reconnectionFigure 4-32 Network Menu - Wireless 4.7.2 Wireless SettingsAPN Access Point Name By local ISP setting 4.7.3 Mobile Connection SettingsNOTE For more reliable email service, use the server’s IP address 4.7.4 Email SettingsEverfocusDDNS 4.7.5 DDNS Settingscharacters particularly ~ ! @ # $ % & * + Host name Host name created through the dyndns account Password Password of the dyndns accountUser name User name of the dyndns account Click button to return to the previous level of menuFigure 4-37 Network Menu - Alarm Server 4.7.6 Alarm Server Settings4.8.1 User 4.8 SYSTEMFigure 4-40 System-User-Add EditFigure 4-41 System-User-Edit Local LocalRS232 4.8.2 I/O ControlControl RS485Everfocus. NOTE all cameras on the bus must use the same protocol Figure 4-43 System-I/O Control-GPS ControlDisk Info 4.8.3 DISK InfoFrom 4.8.4 LOGLog Type Export Log to USB Press button to export log data to USB Clear Log Press button to clear the logPrev Page Go to the previous page of log Next Page Go to the next page of log Close Close the windowFigure 4-48 System-Settings 4.8.5 SETTINGSConfigurations 4.8.6 SERVICEFirmware 4.9 INFORMATION Network Select network type from LAN, Wireless and MobileSystem Status5.1 Introduction to TCP/IP 5 Networking Overview5.2 Subnet Masks 5.3 Gateway Address5.4 Virtual Ports 5.5 Pre-Installation5.6 What is your Network Setup? Crossover Ethernet Cable Pin outs 5.7 Simple One to One ConnectionConnection Procedure Page Page  Restart both the computer and the DVR  Click on the option that says “Use the following IP address”Straight Through Ethernet Cable Pin outs 5.8 Direct High Speed Modem ConnectionConnection Procedure  Note If you have a dynamic IP address, you can set the DVR to DHCP to automatically detect the network settings. Therefore, it can use a dynamic IP address Connection Procedure 5.9 Router or LAN ConnectionStraight Through Ethernet Cable Pin outs  Exit from the Menu to save settings To manually assign an address  Log into the EverFocus DVR menu and go to the Network Setting Menuo If using Windows Vista, choose Search instead  Type “command” and click on OKTo set DVR for Internet Connection through router 6 REMOTE OPERATION FROM BROWSER 6.1 CONNECTING TO EMV400Chapter 6.2.1 Installing ActiveX controls 6.2 BROWSER SECURITY SETTINGPage Right click on the yellow bar and select “Run Add-on…” Install the MSXML file when prompted to do soNow, you will be able to see the remote live page 6.2.2 Enabling ActiveX Controls “Prompt” “Enable”Install the ePlusDVR.cab file when prompted to do so Close the window so you are back at the login screenDefault password Click the Refresh button to reload the page6.3 REMOTE LIVE VIEW System Setup Information Setup Copy Menu Search Menu Alarm/Event Setup Date/Time Setup Display Setup Network Setup5. In the main page, you will see live images in a 4-screen display Playback Control Keys 6.4 REMOTE PLAYBACKFast rewind the video Play Reverse the videoChapter 7 EVERFOCUS DDNS SETUPStep 5. You should now be able to connect by typing the name you created into the address bar. Example http//hostname.everfocusddns.com 8.1 TYPICAL LINKSYS PORT FORWARDING 8 LINKSYS & D-LINK PORT FORWARDINGChapter Here is an example for how the port information might look 8.2 TYPICAL D-LINK PORT FORWARDING Virtual Server - Select Enabled or Disabled Schedule  The DVR will not go into record mode 9 TROUBLESHOOTING The DVR displays nothing on the main monitor  There is no display coming from one of the channels on the DVRPage Appendix APPENDIX A TIMING OF ALARM MODESt Event Alarm Reset Input Event Alarm Durationt Duration = t Reaction Timeout Mode Retrigger of Alarms Record Mode Normal + Event CaseRecord With Recording days APPENDIX B EXPRESS SETUP RECORDING VALUE SELECTION RULESCase Record Mode Normal + Event or Event Only Record With Preset SettingPreset Setting Option Appendix APPENDIX C REMOTE CONTROLBeijing office Headquarter OfficeEuropean Office Japan Office