Manuals / EverFocus / TV and Video / DVR

EverFocus EMV400 user manual Service, Firmware, Configurations

Models: EMV400

1 129

Download 129 pages 3.46 Kb

Page 89

4.8.6 SERVICE

4.8.6 SERVICE

Figure 4-49 System-Service.

Firmware

Current Firmware Version: Displays the current version.

Upgrade from USB: Press “Upgrade” to upgrade the firmware.

NOTE: To perform a Firmware Upgrade, you will need to connect a USB flash device with the desired firmware. Do not disconnect the USB device or turn off the power to the unit during the upgrade; this can cause the system to fail to recover, requiring factory service to repair.

Configurations

Load Factory Default: Click “Load” to restore all menu settings to the default values. User Account, Network IP Settings, and Time are not affected.

Load From USB: Click “Load” to upload saved DVR configuration settings from a USB flash device.

Save To USB: Click “’Save” to save the current DVR configuration settings to a USB flash device.

Click button to return to the previous level of menu.

81

Image 89

EverFocus EMV400 user manual Service, Firmware, Configurations

Contents

User Manual EMV400 DVRRelease Date Oct EMV400 DVR Instruction Manual Cleaning Safety Precautions Read Instructions  Retain Instructions Attachments  Power Cord Protection Water and Moisture  ServicingWEEE DVR CONFIGURATION CONFIGURATIONMOUSE OPERATION TABLE OF CONTENTS6 REMOTE OPERATION FROM BROWSER NETWORKING OVERVIEWInstalling ActiveX controls BROWSER SECURITY SETTING6.2.1 6.2.2Chapter 1.1 FEATURES1 PRODUCT OVERVIEW  Temperature -20ºC ~ 55ºC Operating, -20ºC ~ 85ºC Non-Operating 1.2 PACKAGE CONTENTSScrews x 1 pack Antenna x 1 set IR Remote Control x Battery x Camera Power cable x Video & Audio cable x Alarm cable xEMV400 - 4CH Mobile DVR 1.3 SPECIFICATIONSRequires real time network connectivity though cellular or WiFi Multiple email notifications in response to alarms and eventsservice Embedded 3-axis G Sensor data recorded alarm if separate user1.4 FRONT PANEL Record This LED ON indicates Record active Power This LED ON indicates Power onFigure 1-2 Rear Panel 1.5 REAR PANEL4 GPS Data Input Connect this connector to GPS receiver via GPS cable Please refer to the following diagrams for the system connections 1.6 SYSTEM CONNECTIONALARM IN 1.7 REAR PANEL CONNECTORPOWER CAM POWER2 CAM POWER112V OUT 12V OUTInterface Interface 1.8 INSTALLATION OF EMV400Suspend  Show all the possible ways to mount the DVR Use the two Z-brackets supplied to mount it in any ways shown Equipment Required Quick Installation Guide  Unpack EverythingPage Trunk Users are suggested to use “suspend” for mounting option  Installing the Cameras and Monitor 1.10 AUDIO INSTALLATION 1.9 VIDEO INPUTS/OUTPUTS INSTALLATION1.11ALARM CONTACTS INSTALLATION 1.11.1 Alarm Input Contacts 1.12 USB-Mouse installation1.11.2 Alarm Output Relay 1.13 NETWORK CONNECTION1.13.2 Network Connection through Patch Cable 1.13.1 Direct PC Connection through Crossover Network CableFigure 1-3 Direct PC Connection Figure 1-4 Network Connection through Patch CablePinout of straight patch cable 1.14 FINAL INSTALL PROCESS2 MOUSE OPERATION 2.1.1 How to select a channel2.1 GENERAL USB MOUSE OPERATION 2.1.2 OSD Root Menu2.1.3 Field Input Options 3.1 CONFIGURATION OF DVR 3 CONFIGURATION3.2 LOGIN ChapterFigure 3-2 On-screen Keyboard 3.3 On Screen Configuration MenuFigure 3-3 On-screen Configuration Playback Bar 3.4.1 Time Search 3.4 SEARCH3.4.2 G Sensor Search Figure 3-6 Search Menu - GPS Search 3.4.3 GPS Speed SearchFigure 3-7 Search Menu - GPS Bordering Search button to return to the previous level of menuFigure 3-8 Search Menu - Event Search 3.4.4 Event SearchPlay Playback selected item Delete Delete selected item Prev Page Go to previous page Next Page Go to next pageClick button to return to the previous level of menu Click button to enter G Sensor search menuFigure 3-10 Archive Menu 3.5 ARCHIVE USBChapter 4 DVR CONFIGURATION4.1 Configuration Menu Figure 4-2 Configuration Menu 4.2.1 Normal 4.2 CAMERA SETTINGFigure 4-5 Camera Settings-Video Loss 4.2.2 Video AdjustSpeed 4.2.3 Alarm4.3.1 Record 4.3 RECORD SETTING4.4.1 Alarm-Alarm Settings 4.4 ALARM/GPSEnable Check box to enable response to that alarm trigger Alarm Select the alarm input trigger connection number from 1 toTransparent Alarm output remains as long as the alarm input is active Buzzer Check this box to enable the buzzer when an alarm occursFigure 4-10 Alarm - Event Settings 4.4.2 Alarm-Event SettingsFigure 4-11 Alarm - Event - Fan Failure Fan FailureFigure 4-12 Alarm - Event - HD Temperature HD TemperatureFigure 4-13 Alarm - Event - HD Failure HD FailureFigure 4-14 Alarm - Event - HD Full HD FullFigure 4-15 Alarm - Event - HD Off HD OffFigure 4-16 Alarm - Event - Power Loss Power LossFigure 4-17 Alarm - Event - Network Loss Network LossFigure 4-18 Alarm - Event - GPS Loss GPS LossFigure 4-19 Alarm - Video Loss 4.4.3 Alarm - Video LossPage Figure 4-20 Alarm - G-Sensor 4.4.4 Alarm-G-Sensor SettingsFigure 4-21 Alarm - GPS Speed 4.4.5 Alarm-GPS SpeedFigure 4-22 Alarm - GPS Event Action 4.4.6 Alarm-GPS Event ActionFigure 4-23 Alarm - GPS Fencing 4.4.7 Alarm-GPS Fencing4.5.1 Date/Time Settings 4.5 Date/Time SettingFigure 4-25 Date/Time Settings-Daylight Saving 4.5.2 Daylight Saving4.6.2 Monitor On Screen Display 4.6 Display4.6.1 Title Main Monitor Click button to set up Layout parameters 4.6.3 Layout4 Up Type Layout type for the display switch Main MonitorFigure 4-29 Display-Sequence 4.6.4 Sequence4.7.1 LAN Settings 4.7 NETWORK SETTINGNetwork Type Well Known Ports 0 thru Registered Ports 1024 thru The default port for the EMV400 isDynamic and/or Private Ports 49152 thru Click button to start LAN reconnectionFigure 4-32 Network Menu - Wireless 4.7.2 Wireless SettingsAPN Access Point Name By local ISP setting 4.7.3 Mobile Connection SettingsNOTE For more reliable email service, use the server’s IP address 4.7.4 Email Settingscharacters particularly ~ ! @ # $ % & * + 4.7.5 DDNS SettingsEverfocusDDNS Host name Host name created through the dyndns account Password Password of the dyndns accountUser name User name of the dyndns account Click button to return to the previous level of menuFigure 4-37 Network Menu - Alarm Server 4.7.6 Alarm Server Settings4.8.1 User 4.8 SYSTEMFigure 4-41 System-User-Edit EditFigure 4-40 System-User-Add Local LocalRS232 4.8.2 I/O ControlEverfocus. NOTE all cameras on the bus must use the same protocol RS485Control Figure 4-43 System-I/O Control-GPS ControlDisk Info 4.8.3 DISK InfoLog Type 4.8.4 LOGFrom Export Log to USB Press button to export log data to USB Clear Log Press button to clear the logPrev Page Go to the previous page of log Next Page Go to the next page of log Close Close the windowFigure 4-48 System-Settings 4.8.5 SETTINGSFirmware 4.8.6 SERVICEConfigurations 4.9 INFORMATION Network Select network type from LAN, Wireless and MobileSystem Status5.1 Introduction to TCP/IP 5 Networking Overview5.2 Subnet Masks 5.3 Gateway Address5.4 Virtual Ports 5.5 Pre-Installation5.6 What is your Network Setup? Crossover Ethernet Cable Pin outs 5.7 Simple One to One ConnectionConnection Procedure Page Page  Restart both the computer and the DVR  Click on the option that says “Use the following IP address”Connection Procedure 5.8 Direct High Speed Modem ConnectionStraight Through Ethernet Cable Pin outs  Note If you have a dynamic IP address, you can set the DVR to DHCP to automatically detect the network settings. Therefore, it can use a dynamic IP address Straight Through Ethernet Cable Pin outs 5.9 Router or LAN ConnectionConnection Procedure  Exit from the Menu to save settings To manually assign an address  Log into the EverFocus DVR menu and go to the Network Setting Menuo If using Windows Vista, choose Search instead  Type “command” and click on OKTo set DVR for Internet Connection through router Chapter 6.1 CONNECTING TO EMV4006 REMOTE OPERATION FROM BROWSER 6.2.1 Installing ActiveX controls 6.2 BROWSER SECURITY SETTINGPage Now, you will be able to see the remote live page Install the MSXML file when prompted to do soRight click on the yellow bar and select “Run Add-on…” 6.2.2 Enabling ActiveX Controls “Prompt” “Enable”Install the ePlusDVR.cab file when prompted to do so Close the window so you are back at the login screenDefault password Click the Refresh button to reload the page6.3 REMOTE LIVE VIEW 5. In the main page, you will see live images in a 4-screen display Alarm/Event Setup Date/Time Setup Display Setup Network SetupSystem Setup Information Setup Copy Menu Search Menu Playback Control Keys 6.4 REMOTE PLAYBACKFast rewind the video Play Reverse the videoChapter 7 EVERFOCUS DDNS SETUPStep 5. You should now be able to connect by typing the name you created into the address bar. Example http//hostname.everfocusddns.com Chapter 8 LINKSYS & D-LINK PORT FORWARDING8.1 TYPICAL LINKSYS PORT FORWARDING Here is an example for how the port information might look 8.2 TYPICAL D-LINK PORT FORWARDING Virtual Server - Select Enabled or Disabled Schedule  The DVR will not go into record mode 9 TROUBLESHOOTING The DVR displays nothing on the main monitor  There is no display coming from one of the channels on the DVRPage Appendix APPENDIX A TIMING OF ALARM MODESt Duration = t Reaction Alarm Reset Input Event Alarm Durationt Event Timeout Mode Retrigger of Alarms Record Mode Normal + Event CaseRecord With Recording days APPENDIX B EXPRESS SETUP RECORDING VALUE SELECTION RULESPreset Setting Option Record With Preset SettingCase Record Mode Normal + Event or Event Only Appendix APPENDIX C REMOTE CONTROLBeijing office Headquarter OfficeEuropean Office Japan Office