Manuals / EverFocus / Computer Equipment / Switch

EverFocus ESM316T002R user manual MAC Filtering Setting, Hint§

Models: ESM316T002R

1 60

Download 60 pages 19.19 Kb

Page 47

MAC Filtering Setting

MAC Filtering Setting

The MAC Filtering pages are used to filter service to clients attempting to access the Internet based on protocol type, destination/source MAC address, and the direction of traffic for each packet.

Web Smart switch interface

To configure MAC Address Filtering:

1.Click Security, MAC Address, MAC Address Filtering.

2.Specify the MAC address to be filtered.

3.Specify the VLAN ID.

4.Select to filter the MAC address as the source, destination, or both.

5.Set a name to describe the filter.

6.Click Add.

Figure 35: MAC Filtering Setting

Hint§

The following parameters are shown on the LLDP Neighbors page.

■MAC Address - Physical address of a device.

■VLAN ID - The ID of a configured VLAN (1-4094).

■Filter - Filter traffic matching the MAC address in packets. (Options: Source MAC, Destination MAC, Both; Default: Source MAC)

■Destination MAC - Filter packets with a matching destination MAC address.

■Source MAC - Filter packets with a matching source MAC address.

■Both - Filter packets with a matching the source or destination MAC address.

■Name – A descriptive name for the MAC address filter.

47

Image 47

EverFocus ESM316T002R user manual MAC Filtering Setting, Hint§

Contents

ESM316T002R GIGABIT MANAGED ETHERNET SWITCH 16 PoE+ PORTSUSER MANUAL PLUS TWO SFP PORTSCHAPTER ContentCHAPTER 3 Configuration CHAPTERCHAPTER 6 Tools CHAPTER 4 SecurityCHAPTER 5 Monitoring Revision History ABOUT THIS GUIDEFeatures Overview Web Browser CHAPTER 1 The IntroductionLogging In Figure 3 Web-Based Management Interface System Information IP Address SettingCHAPTER 2 System Hint§ IPv6 Address SettingFigure 7 User Account Setting Port SettingUser Account Hint§ State-Set the link state of port interfaces. Default EnabledFigure 9 Trunk Group Setting CHAPTER 3 ConfigurationTrunk Group Setting Hint§ Trunk Distribution Algorithm SettingFigure 10 Trunk Distribution Algorithm Setting Page Hint§ LACP SettingFigure 11 LACP Setting Hint§ Static VLAN Table SettingHint§ VLAN Port SettingFigure 13 VLAN Port Setting Hint§ VLAN-Stacking Table SettingFigure 15 VLAN Stacking Setting Vlan Stacking SettingHint§ Hint§ IGMP Multicast Group InformationFigure 17 IGMP Snooping IGMP Snoopingruns on Layer 2 switch to manage and control multicast groups Hint§ IGMP Global SettingHint§ IGMP VLAN SettingHint§ Spanning TreeFigure 18 spanning tree settings Minimum Maximum The lower of 10 or Max. Message Age / 2 Maximum The lower of 40 or 2 x Forward Delay DefaultMinimum The higher of 4 or Max. Message Age / 2 + Maximum Default Minimum The higher of 6 or 2 x Hello Time +Hint§ Spanning Tree Port SettingFigure 19 spanning tree port settings P2P - The point-to-point setting for the port Disabled - There is no connection on the portPath Cost - The path cost setting for the port Config - The administrator configured path cost settingHint§ Quality of Service QoSPort-based Priority Setting Figure 20 Port-based Priority SettingHint§ DSCP-based Priority SettingHint§ Priority to Queue Mapping SettingFigure 22 Priority to Queue Mapping Setting Hint§ Packet Scheduling SettingFigure 23 Packet Scheduling Setting Hint§ LLDP ConfigurationsFigure 24 LLDP Settings Figure 25 LLDP Neighbors LLDP NeighborsHint§ SNMP Setting Hint§ Trap Receivers SettingHint§ Hint§ Port Mirroring SettingHint§ Port Security SettingForward No action is taken. Traffic is forwarded as normal Trap to CPU Send an SNMP trap message. This is the defaultDrop Drop other traffic from the port Hint§ Bandwidth Control SettingState - Enable or disable the rate limit. Default Disabled Type - Specify ingress or egress traffic. Default IngressHint§ Jumbo Frame SettingFigure 30 Jumbo Frame Setting Hint§ Management Access FilterFigure 31 Management Access Filter Hint§ Power over Ethernet SettingFigure 32 Power over Ethernet Hint§ CHAPTER 4 SecurityMAC Address Information Hint§ Static MAC SettingHint§ MAC Filtering SettingFigure 35 MAC Filtering Setting Hint§ 802.1x SettingHint§ 802.1x Port SettingFigure 37 802.1x Port Setting Hint§ IP Filter ConfigurationsFigure 38 IP Filter Configurations allowed 255.255.255.0Hint§ Storm Control settingsFigure 39 Storm Control settings Figure 40 Port Isolation Port IsolationHint§ Figure 41 Defence Engine Defence EngineHint§ Hint§ CHAPTER 5 MonitoringPort Statistics Information Hint§ Http UpgradeCHAPTER 6 Tools Figure 44 Reset Reset Factory DefaultsTo restore factory defaults Web Smart switch interface SPECIFICATIONS Reboot‐ LAN settings IP address, Gateway, etc Backplane speed 36 Gbps Switch architecture store and forwardConfiguration options ‐ Quality of Service QoS port-‐based or DSCP