Manuals / EverFocus / Computer Equipment / Switch

EverFocus ESM316T002R user manual Web-Based Management Interface

Models: ESM316T002R

1 60

Download 60 pages 19.19 Kb

Page 7

Figure 3: Web-Based Management Interface

Figure 3: Web-Based Management Interface

7

Image 7

EverFocus ESM316T002R user manual Web-Based Management Interface

Contents

ESM316T002R GIGABIT MANAGED ETHERNET SWITCH 16 PoE+ PORTSUSER MANUAL PLUS TWO SFP PORTSCHAPTER ContentCHAPTER 3 Configuration CHAPTERCHAPTER 5 Monitoring CHAPTER 4 SecurityCHAPTER 6 Tools Features Overview ABOUT THIS GUIDERevision History Web Browser CHAPTER 1 The IntroductionLogging In Figure 3 Web-Based Management Interface CHAPTER 2 System IP Address SettingSystem Information Hint§ IPv6 Address SettingUser Account Port SettingFigure 7 User Account Setting Hint§ State-Set the link state of port interfaces. Default EnabledTrunk Group Setting CHAPTER 3 ConfigurationFigure 9 Trunk Group Setting Figure 10 Trunk Distribution Algorithm Setting Trunk Distribution Algorithm SettingHint§ Page Figure 11 LACP Setting LACP SettingHint§ Hint§ Static VLAN Table SettingFigure 13 VLAN Port Setting VLAN Port SettingHint§ Hint§ VLAN-Stacking Table SettingFigure 15 VLAN Stacking Setting Vlan Stacking SettingHint§ Hint§ IGMP Multicast Group Informationruns on Layer 2 switch to manage and control multicast groups IGMP SnoopingFigure 17 IGMP Snooping Hint§ IGMP Global SettingHint§ IGMP VLAN SettingFigure 18 spanning tree settings Spanning TreeHint§ Minimum Maximum The lower of 10 or Max. Message Age / 2 Maximum The lower of 40 or 2 x Forward Delay DefaultMinimum The higher of 4 or Max. Message Age / 2 + Maximum Default Minimum The higher of 6 or 2 x Hello Time +Figure 19 spanning tree port settings Spanning Tree Port SettingHint§ P2P - The point-to-point setting for the port Disabled - There is no connection on the portPath Cost - The path cost setting for the port Config - The administrator configured path cost settingHint§ Quality of Service QoSPort-based Priority Setting Figure 20 Port-based Priority SettingHint§ DSCP-based Priority SettingFigure 22 Priority to Queue Mapping Setting Priority to Queue Mapping SettingHint§ Figure 23 Packet Scheduling Setting Packet Scheduling SettingHint§ Figure 24 LLDP Settings LLDP ConfigurationsHint§ Hint§ LLDP NeighborsFigure 25 LLDP Neighbors SNMP Setting Hint§ Trap Receivers SettingHint§ Hint§ Port Mirroring SettingHint§ Port Security SettingDrop Drop other traffic from the port Trap to CPU Send an SNMP trap message. This is the defaultForward No action is taken. Traffic is forwarded as normal Hint§ Bandwidth Control SettingState - Enable or disable the rate limit. Default Disabled Type - Specify ingress or egress traffic. Default IngressFigure 30 Jumbo Frame Setting Jumbo Frame SettingHint§ Figure 31 Management Access Filter Management Access FilterHint§ Figure 32 Power over Ethernet Power over Ethernet SettingHint§ MAC Address Information CHAPTER 4 SecurityHint§ Hint§ Static MAC SettingFigure 35 MAC Filtering Setting MAC Filtering SettingHint§ Hint§ 802.1x SettingFigure 37 802.1x Port Setting 802.1x Port SettingHint§ Figure 38 IP Filter Configurations IP Filter ConfigurationsHint§ allowed 255.255.255.0Figure 39 Storm Control settings Storm Control settingsHint§ Hint§ Port IsolationFigure 40 Port Isolation Hint§ Defence EngineFigure 41 Defence Engine Port Statistics Information CHAPTER 5 MonitoringHint§ CHAPTER 6 Tools Http UpgradeHint§ To restore factory defaults Web Smart switch interface Reset Factory DefaultsFigure 44 Reset SPECIFICATIONS Reboot‐ LAN settings IP address, Gateway, etc Backplane speed 36 Gbps Switch architecture store and forwardConfiguration options ‐ Quality of Service QoS port-‐based or DSCP