Manuals / EverFocus / Computer Equipment / Switch

EverFocus ESM316T002R user manual 255.255.255.0, allowed

Models: ESM316T002R

1 60

Page 51

■IP Address — An IP address, or an address specifying a range, that is allowed access through the switch. ■IP Netmask — A mask that specifies a single IP address, or defines a range of IP addresses. (Default:

255.255.255.0)

■DHCP Server Allowed — Permit traffic from a DHCP server through the specified ports. (Default: All ports

allowed)

Page 51

Image 51

EverFocus ESM316T002R user manual 255.255.255.0, allowed

Contents

ESM316T002R GIGABIT MANAGED ETHERNET SWITCH 16 PoE+ PORTSUSER MANUAL PLUS TWO SFP PORTSCHAPTER ContentCHAPTER 3 Configuration CHAPTERCHAPTER 4 Security CHAPTER 5 MonitoringCHAPTER 6 Tools ABOUT THIS GUIDE Features OverviewRevision History Web Browser CHAPTER 1 The IntroductionLogging In Figure 3 Web-Based Management Interface IP Address Setting CHAPTER 2 SystemSystem Information Hint§ IPv6 Address SettingPort Setting User AccountFigure 7 User Account Setting Hint§ State-Set the link state of port interfaces. Default EnabledCHAPTER 3 Configuration Trunk Group SettingFigure 9 Trunk Group Setting Trunk Distribution Algorithm Setting Figure 10 Trunk Distribution Algorithm SettingHint§ Page LACP Setting Figure 11 LACP SettingHint§ Hint§ Static VLAN Table SettingVLAN Port Setting Figure 13 VLAN Port SettingHint§ Hint§ VLAN-Stacking Table SettingFigure 15 VLAN Stacking Setting Vlan Stacking SettingHint§ Hint§ IGMP Multicast Group InformationIGMP Snooping runs on Layer 2 switch to manage and control multicast groupsFigure 17 IGMP Snooping Hint§ IGMP Global SettingHint§ IGMP VLAN SettingSpanning Tree Figure 18 spanning tree settingsHint§ Minimum Maximum The lower of 10 or Max. Message Age / 2 Maximum The lower of 40 or 2 x Forward Delay DefaultMinimum The higher of 4 or Max. Message Age / 2 + Maximum Default Minimum The higher of 6 or 2 x Hello Time +Spanning Tree Port Setting Figure 19 spanning tree port settingsHint§ P2P - The point-to-point setting for the port Disabled - There is no connection on the portPath Cost - The path cost setting for the port Config - The administrator configured path cost settingHint§ Quality of Service QoSPort-based Priority Setting Figure 20 Port-based Priority SettingHint§ DSCP-based Priority SettingPriority to Queue Mapping Setting Figure 22 Priority to Queue Mapping SettingHint§ Packet Scheduling Setting Figure 23 Packet Scheduling SettingHint§ LLDP Configurations Figure 24 LLDP SettingsHint§ LLDP Neighbors Hint§Figure 25 LLDP Neighbors SNMP Setting Trap Receivers Setting Hint§Hint§ Hint§ Port Mirroring SettingHint§ Port Security SettingTrap to CPU Send an SNMP trap message. This is the default Drop Drop other traffic from the portForward No action is taken. Traffic is forwarded as normal Hint§ Bandwidth Control SettingState - Enable or disable the rate limit. Default Disabled Type - Specify ingress or egress traffic. Default IngressJumbo Frame Setting Figure 30 Jumbo Frame SettingHint§ Management Access Filter Figure 31 Management Access FilterHint§ Power over Ethernet Setting Figure 32 Power over EthernetHint§ CHAPTER 4 Security MAC Address InformationHint§ Hint§ Static MAC SettingMAC Filtering Setting Figure 35 MAC Filtering SettingHint§ Hint§ 802.1x Setting802.1x Port Setting Figure 37 802.1x Port SettingHint§ IP Filter Configurations Figure 38 IP Filter ConfigurationsHint§ allowed 255.255.255.0Storm Control settings Figure 39 Storm Control settingsHint§ Port Isolation Hint§Figure 40 Port Isolation Defence Engine Hint§Figure 41 Defence Engine CHAPTER 5 Monitoring Port Statistics InformationHint§ Http Upgrade CHAPTER 6 ToolsHint§ Reset Factory Defaults To restore factory defaults Web Smart switch interfaceFigure 44 Reset SPECIFICATIONS Reboot‐ LAN settings IP address, Gateway, etc Backplane speed 36 Gbps Switch architecture store and forwardConfiguration options ‐ Quality of Service QoS port-‐based or DSCP