Manuals / EverFocus / Computer Equipment / Switch

EverFocus ESM316T002R user manual Type - Specify ingress or egress traffic. Default Ingress

Models: ESM316T002R

1 60

Download 60 pages 19.19 Kb

Page 41

Image 41

■Type - Specify ingress or egress traffic. (Default: Ingress)

■State - Enable or disable the rate limit. (Default: Disabled)

■Rate (Kbit/sec) - Set the rate limit level. (Range: 0 - 1048544 Kbps in steps of 16)

Page 41

Image 41

EverFocus ESM316T002R user manual Type - Specify ingress or egress traffic. Default Ingress

Contents

USER MANUAL GIGABIT MANAGED ETHERNET SWITCH 16 PoE+ PORTSPLUS TWO SFP PORTS ESM316T002RCHAPTER 3 Configuration ContentCHAPTER CHAPTERCHAPTER 6 Tools CHAPTER 4 SecurityCHAPTER 5 Monitoring Revision History ABOUT THIS GUIDEFeatures Overview Web Browser CHAPTER 1 The IntroductionLogging In Figure 3 Web-Based Management Interface System Information IP Address SettingCHAPTER 2 System Hint§ IPv6 Address SettingFigure 7 User Account Setting Port SettingUser Account Hint§ State-Set the link state of port interfaces. Default EnabledFigure 9 Trunk Group Setting CHAPTER 3 ConfigurationTrunk Group Setting Hint§ Trunk Distribution Algorithm SettingFigure 10 Trunk Distribution Algorithm Setting Page Hint§ LACP SettingFigure 11 LACP Setting Hint§ Static VLAN Table SettingHint§ VLAN Port SettingFigure 13 VLAN Port Setting Hint§ VLAN-Stacking Table SettingFigure 15 VLAN Stacking Setting Vlan Stacking SettingHint§ Hint§ IGMP Multicast Group InformationFigure 17 IGMP Snooping IGMP Snoopingruns on Layer 2 switch to manage and control multicast groups Hint§ IGMP Global SettingHint§ IGMP VLAN SettingHint§ Spanning TreeFigure 18 spanning tree settings Minimum The higher of 4 or Max. Message Age / 2 + Maximum Default Maximum The lower of 40 or 2 x Forward Delay DefaultMinimum The higher of 6 or 2 x Hello Time + Minimum Maximum The lower of 10 or Max. Message Age / 2Hint§ Spanning Tree Port SettingFigure 19 spanning tree port settings Path Cost - The path cost setting for the port Disabled - There is no connection on the portConfig - The administrator configured path cost setting P2P - The point-to-point setting for the portPort-based Priority Setting Quality of Service QoSFigure 20 Port-based Priority Setting Hint§Hint§ DSCP-based Priority SettingHint§ Priority to Queue Mapping SettingFigure 22 Priority to Queue Mapping Setting Hint§ Packet Scheduling SettingFigure 23 Packet Scheduling Setting Hint§ LLDP ConfigurationsFigure 24 LLDP Settings Figure 25 LLDP Neighbors LLDP NeighborsHint§ SNMP Setting Hint§ Trap Receivers SettingHint§ Hint§ Port Mirroring SettingHint§ Port Security SettingForward No action is taken. Traffic is forwarded as normal Trap to CPU Send an SNMP trap message. This is the defaultDrop Drop other traffic from the port Hint§ Bandwidth Control SettingState - Enable or disable the rate limit. Default Disabled Type - Specify ingress or egress traffic. Default IngressHint§ Jumbo Frame SettingFigure 30 Jumbo Frame Setting Hint§ Management Access FilterFigure 31 Management Access Filter Hint§ Power over Ethernet SettingFigure 32 Power over Ethernet Hint§ CHAPTER 4 SecurityMAC Address Information Hint§ Static MAC SettingHint§ MAC Filtering SettingFigure 35 MAC Filtering Setting Hint§ 802.1x SettingHint§ 802.1x Port SettingFigure 37 802.1x Port Setting Hint§ IP Filter ConfigurationsFigure 38 IP Filter Configurations allowed 255.255.255.0Hint§ Storm Control settingsFigure 39 Storm Control settings Figure 40 Port Isolation Port IsolationHint§ Figure 41 Defence Engine Defence EngineHint§ Hint§ CHAPTER 5 MonitoringPort Statistics Information Hint§ Http UpgradeCHAPTER 6 Tools Figure 44 Reset Reset Factory DefaultsTo restore factory defaults Web Smart switch interface SPECIFICATIONS RebootConfiguration options Backplane speed 36 Gbps Switch architecture store and forward‐ Quality of Service QoS port-‐based or DSCP ‐ LAN settings IP address, Gateway, etc