Manuals / Extron electronic / Home Audio / Stereo System

Extron electronic DMP 44 LC The Firmware Loader screen appears, The firmware upload is complete

Models: DMP 44 LC

1 81

Download 81 pages 20.93 Kb

Page 79

The Firmware Loader screen appears.

The Firmware Loader screen appears.

3.From the toolbar, select File > Open.

4.Locate the downloaded firmware file and click on it.

5.Click Begin on the main screen. The total progress bar tracks the loading progress.

6.When the upload is finished, exit the program by selecting File > Exit.

The firmware upload is complete.

DMP 44 LC • Reference Information

73

Image 79

Extron electronic DMP 44 LC manual The Firmware Loader screen appears, From the toolbar, select File > Open

Contents

Four-LineInput and Four-LineOutput DMP 44 LCUser Guide Audio Products Mixers and ProcessorsInstrucciones de seguridad • Español Safety Instructions • EnglishConsignes de Sécurité • Français Sicherheitsanleitungen • DeutschFCC Class A Notice Copyright Conventions Used in this GuideTrademarks Contents DMP 44 LC • Contents About the DMP 44 LC Digital Matrix Processor FeaturesIntroduction About This GuideDMP 44 LC Introduction USB 2.0 port on the front panel DVI Switcher DMP 44 LC Application DiagramMediaLink Switcher Power AmplierRear Panel Features and Cabling InstallationRear Panel Features and Cabling Mounting the DMP 44 LCFigure 2. Power Supply Wiring Figure 5. RS-232Wiring Audio Input WiringAudio Output Wiring Figure 4. Output Connector WiringDMP 44 LC • Installation USB Configuration port front panel•DMP 44 LC Operation •Front Panel Operation OperationDMP 44 LC Operation •Rear Panel Operation •DSP Processing/Signal FlowFigure 6. DMP 44 LC Front Panel Power CycleFront Panel Operation Rear Panel OperationThe default reset state of the device is Firmware UpdatesReset Actuator and LED Hardware Reset ModesDigital Input Ports 6.Select Apply to accept the changes Line Input Signal Chain DSP Processing and Signal FlowDMP 44 LC • Operation Mix MatrixLine Output Chain Processor BlocksLine Input Gain Line Input ChannelsFigure 8. Filter Block Dialog Box Filter BlockFigure 10. Filter Dialog Box, Filter Not Bypassed Figure 9. Filter Dialog Box, Filters AddedDMP 44 LC • Operation Figure 11. Parametric Filter Dialog Box, 1000 Hz Parametric EqualizerFigure 12. All Parametric Filters Active Figure 14. Low Pass Filter Response Curve High PassLow Pass Figure 13. High Pass Filter Response CurveBass and Treble Shelving Setting bass and treble filtersFigure 15. Bass and Treble Shelving 2. To add a new group, select Add a Group Configuring Groups2.Specify bass and treble filters if necessary 1.From the View menu, select Group ControlsDMP 44 LC • Operation 3.Select a group to configureTreble Groups.” 4.Select a control type for the group5.Define the group members Configuring Bass and Treble GroupsDMP 44 LC • Operation DMP 44 LC • Operation 6.Select the group members 5.Select the Bass or Treble control groupDMP 44 LC • Operation Compressor Dynamics ProcessorDefault is -30.0dB Ducking LimiterDMP 44 LC • Operation Figure 16. Ducker Configuration DialogDSettings Ducking Configuration DialogACurrent source indicator BEnable source mic/line checkboxFigure 17. Ducker Configuration, Input Priority PriorityFBy dB Figure 18. Mix Matrix Outlined in Red Mix MatrixDMP 44 LC Operation Mix-pointGUI behaviorDMP 44 LC • Operation Figure 20. All Inputs to Output Figure 19. Input 1 to OutputDMP 44 LC • Operation Filter Line Output ChannelsFigure 21. All Inputs to All Outputs Dynamics VolumeDMP 44 LC • Operation •Command/Response Table for Basic SIS Commands SIS Programming and ControlConnection Options RS-232PortFigure 22. ASCII to Hex Conversion Table Using the Command/Response TablesUSB Port front panel DMP 44 LC-initiatedMessagesSymbol definitions Command/Response Table OverviewCommand/Response Table for Basic SIS Commands Error ResponsesASCII Command General commandsSpecial Characters CommandEX#CV Partial preset commands Group Master Commandsname Digital Input Commands “DSP Processing and Signal Flow”section Command/Response Tables for DSP SIS Commandsd e a b c Symbol definitions Command/Response Tables for Audio SIS CommandsResponse CommandASCII Command Special CharactersED X6%*X6^GRPM C Main Mix-point VolumeA Input Gain Control C Main Mix-point•Software Control •DSP Configurator Program Installing the DSP Configurator ProgramSoftware Control Software ControlFigure 25. DVD Control Software Menu Figure 24. DVD Software MenuDMP 44 LC • Software Control Figure 26. USB Installer Splash Screen Install the USB DriverFigure 27. USB Installation Live Mode” DSP Configurator ProgramStarting the Program Figure 28. Successful USB Driver InstallationUsing the Program Synchronizing: Pull vs. Push Emulate Mode vs. Live ModeDMP 44 LC • Software Control Figure 30. Selecting Live Mode DMP 44 LC • Software Control Figure 31. Selecting Live Mode, continued10 11 Presets Figure 32. Preset Preview Previewing/Recalling a PresetSave Preset Building a PresetFigure 33. Save Preset Managing Presets in the GUIDMP 44 LC • Software Control Presets: Pull vs. Push or Create LiveAdvanced Push Configuration - Advanced, Push Presets, AllDMP 44 LC • Software Control Selected3.Select Push Presets “To switch from emulate mode to live mode:”Advanced Audio input SpecificationsReference Information AudioDMP 44 LC • Reference Information Control/remote — audio processorControl — digital input ports GeneralIncluded Parts Part Numbers and AccessoriesAccessories MountingRack Mounting UL Rack Mounting GuidelinesFigure 35. MBU 123, Under-DeskMounting Furniture Mounting1.Select Tools, then Firmware Loader Firmware LoaderDMP 44 LC Reference Information The Firmware Loader screen appears3.From the toolbar, select File > Open The firmware upload is completeDMP 44 LC Reset Mode Summary DMP 44 LC Hardware Reset Modesand Central America Extron WarrantyUSA, Canada, South America Japan