Manuals / Force10 Networks / Computer Equipment / Switch

Force10 Networks CC-C-BLNK-LC manual Technical Specifications, Chassis Physical Design

Models: CC-C-BLNK-LC

1 38

Download 38 pages 44.89 Kb

Page 34

Technical Specifications

Technical Specifications

The MXL 10/40GbE Switch is an I/O module and installed with Server (model: PowerEdge M1000e) for communication.

The product should be operated at an ambient temperature of 50°C.

CAUTION: Lithium Battery Caution: There is a danger of explosion if the battery is incorrectly replaced.

Replace only with same or equivalent type. Dispose batteries according to manufacturer's instructions.

Chassis Physical Design

Parameter	Specifications

Height	1.32 inches (33.45 mm)

Width	10.81 inches (274.75 mm)

Depth	12.17 inches (309.24 mm)

Environmental Parameters

Parameter	Specifications

Operating temperature	32° to 104°F (0° to 40°C)

Operating humidity	10 to 85% (RH), non-condensing

Storage temperature	–40° to 158°F (–40° to 70°C)

Storage humidity	5 to 95% (RH), non-condensing

Maximum thermal output	419.7 BTU/hr

34

Technical Specifications

Image 34

Force10 Networks CC-C-BLNK-LC manual Technical Specifications, Chassis Physical Design, Environmental Parameters

Contents

June Dell Force10 MXL 10/40GbE Switch IO ModuleGetting Started Guide Regulatory Model DF10MXLNotes, Cautions, and Warnings June 2012 P/N WMDP6 Rev. A00Installing the Switch Blade in a PowerEdge M1000e Contents4 Installing and Configuring the Switch Connecting a Console Terminal5 Assembling a Switch Stack 9 Technical Specifications6 Splitting 40GbE QSFP+ Ports into 10GbE SFP+ Configuring and Bringing Up a StackProduct Description IntroductionIntroduction Internal Ports Hardware OverviewFront Panel Base Module FlexIOTM Plug-in ModulesThen save the configuration and reload the switch Port Numbering USB Ports Figure 1-3. USB Ports on Front PanelSystem LED System and Port LEDsFigure 1-4. System LEDs on Front Panel ColorLink Status Activity Link Status Activity Link Status Activity Installation Site PreparationPackage Contents Installing and Configuring the SwitchUnpacking the Switch Unpacking StepsInstalling and Configuring the Switch Insert Switch Blade and Power On Connect ConsoleInstalling the Switch Blade in a PowerEdge M1000e After you slide the MXL 10/40GbE Switch in so that the connectors on the back of the blade touch the chassis midplane, the switch receives power from the chassis and automatically powers on. The chassis management controller CMC in the chassis validates that the switch blade is a supported I/O module before powering it on Page Invoking the X-Loader and U-Boot CLIs Performing the Initial ConfigurationInitial Configuration Procedure Sample Setup Wizard Session set up the initial SNMP version 2 account now To access the switch through any Management Interface you can This is the configuration information that has been collected Assembling a Switch Stack Figure 1-9. Six Stacked MXL 10/40GbE SwitchesConfiguring and Bringing Up a Stack 2 Save the stacking configuration on the 40GbE ports Stack Startup Master and Member SwitchesManaging a Stack Topology DiscoveryFTOS# upgrade system stack-unit unit-number partition Auto Stack Number AssignmentFTOS Version Checking FTOS# upgrade system stack-unit 3 aSystem Initialization Splitting 40GbE QSFP+ Ports into 10GbE SFP+ PortsSwitch Configuration Switch ConfigurationFCoE Connectivity DCB SupportiSCSI Operation Next Steps Next StepsChassis Physical Design Technical SpecificationsEnvironmental Parameters Power Requirements IEEE StandardsTechnical Specifications Page w w w. d e l l . c o m s u p p o r t . d e l l . c o m Printed in the U.S.A