Manuals / Force10 Networks / Computer Equipment / Switch

Force10 Networks CC-C-BLNK-LC manual This is the configuration information that has been collected

Models: CC-C-BLNK-LC

1 38

Download 38 pages 44.89 Kb

Page 24

This is the configuration information that has been collected:

This is the configuration information that has been collected:

SNMP Interface = "mxl1"@1.1.1.1

User Account setup = root

Password = ******

Out-of-band IP address = 192.168.2.1 255.255.255.0

VLAN1 Router Interface IP = 2.2.2.80 255.255.255.0

Default Gateway = 192.168.2.0

If the information is correct, please enter (Y) to save the configuration.

If the information is incorrect, enter (N) to discard the configuration and restart the wizard: [Y/N] y

Thank you for using the Dell Easy Setup Wizard. You will now enter CLI mode.

Applying Interface configuration, please wait ...

FTOS>

NOTE: If you do not save the initial configuration settings, they will be lost at the next switch reboot and the Setup Wizard will be invoked. To save the initial configuration to the startup configuration, enter the following commands at the CLI prompt on the attached console:

FTOS> enable FTOS# write memory

24

Installing and Configuring the Switch

Image 24

Force10 Networks CC-C-BLNK-LC manual This is the configuration information that has been collected

Contents

Dell Force10 MXL 10/40GbE Switch IO Module Getting Started GuideJune Regulatory Model DF10MXLNotes, Cautions, and Warnings June 2012 P/N WMDP6 Rev. A00Contents 4 Installing and Configuring the SwitchInstalling the Switch Blade in a PowerEdge M1000e Connecting a Console Terminal9 Technical Specifications 6 Splitting 40GbE QSFP+ Ports into 10GbE SFP+5 Assembling a Switch Stack Configuring and Bringing Up a StackIntroduction Product DescriptionIntroduction Hardware Overview Internal PortsFront Panel Base Module FlexIOTM Plug-in ModulesThen save the configuration and reload the switch Port Numbering USB Ports Figure 1-3. USB Ports on Front PanelSystem and Port LEDs Figure 1-4. System LEDs on Front PanelSystem LED ColorLink Status Activity Link Status Activity Link Status Activity Installation Site PreparationInstalling and Configuring the Switch Unpacking the SwitchPackage Contents Unpacking StepsInstalling and Configuring the Switch Insert Switch Blade and Power On Connect ConsoleInstalling the Switch Blade in a PowerEdge M1000e After you slide the MXL 10/40GbE Switch in so that the connectors on the back of the blade touch the chassis midplane, the switch receives power from the chassis and automatically powers on. The chassis management controller CMC in the chassis validates that the switch blade is a supported I/O module before powering it on Page Invoking the X-Loader and U-Boot CLIs Performing the Initial ConfigurationInitial Configuration Procedure Sample Setup Wizard Session set up the initial SNMP version 2 account now To access the switch through any Management Interface you can This is the configuration information that has been collected Assembling a Switch Stack Figure 1-9. Six Stacked MXL 10/40GbE SwitchesConfiguring and Bringing Up a Stack 2 Save the stacking configuration on the 40GbE ports Master and Member Switches Managing a StackStack Startup Topology DiscoveryAuto Stack Number Assignment FTOS Version CheckingFTOS# upgrade system stack-unit unit-number partition FTOS# upgrade system stack-unit 3 aSystem Initialization Splitting 40GbE QSFP+ Ports into 10GbE SFP+ PortsSwitch Configuration Switch ConfigurationDCB Support FCoE ConnectivityiSCSI Operation Next Steps Next StepsTechnical Specifications Chassis Physical DesignEnvironmental Parameters Power Requirements IEEE StandardsTechnical Specifications Page w w w. d e l l . c o m s u p p o r t . d e l l . c o m Printed in the U.S.A