Manuals / Force10 Networks / Computer Equipment / Switch

Force10 Networks CC-C-BLNK-LC manual Power Requirements, IEEE Standards

Models: CC-C-BLNK-LC

1 38

Download 38 pages 44.89 Kb

Page 35

Power Requirements

Power Requirements

Parameter	Specifications

Power supply	100–240 VAC 50/60 Hz

Maximum current draw per system	2 A @ 100/120 VAC
	1 A @ 200/40 VAC

Maximum power consumption	123 Watts

Reliability	MTBF 355,178 hours

IEEE Standards

The MXL 10/40GbE Switch complies with the following IEEE standards:

•802.1AB LLDP

•802.1ag Connectivity fault Management

•802.1D Bridging, STP

•802.1p L2 Prioritization

•802.1Q VLAN Tagging, Double VLAN Tagging, GVRP

•802.1s MSTP

•802.1w RSTP

•802.3ab Gigabit Ethernet (1000BASE-T)

•802.3ac Frame Extensions for VLAN Tagging

•802.3ad Link Aggregation with LACP

•802.3ae 10 Gigabit Ethernet (10GBASE-X)

•802.3ba 40 Gigabit Ethernet (40GBase-SR4, 40GBase-CR4) on optical ports

•802.3u Fast Ethernet (100BASE-TX)

•802.3x Flow Control

•802.3z Gigabit Ethernet (1000BASE-X)

•ANSI/TIA-1057 LLDP-MED

•Force10 PVST+

•MTU 12K bytes

Technical Specifications

35

Image 35

Force10 Networks CC-C-BLNK-LC manual Power Requirements, IEEE Standards

Contents

Regulatory Model DF10MXL Dell Force10 MXL 10/40GbE Switch IO ModuleGetting Started Guide JuneJune 2012 P/N WMDP6 Rev. A00 Notes, Cautions, and WarningsConnecting a Console Terminal Contents4 Installing and Configuring the Switch Installing the Switch Blade in a PowerEdge M1000eConfiguring and Bringing Up a Stack 9 Technical Specifications6 Splitting 40GbE QSFP+ Ports into 10GbE SFP+ 5 Assembling a Switch StackIntroduction IntroductionProduct Description Front Panel Hardware OverviewInternal Ports FlexIOTM Plug-in Modules Base ModuleThen save the configuration and reload the switch Port Numbering Figure 1-3. USB Ports on Front Panel USB PortsColor System and Port LEDsFigure 1-4. System LEDs on Front Panel System LEDLink Status Activity Link Status Activity Link Status Activity Site Preparation InstallationUnpacking Steps Installing and Configuring the SwitchUnpacking the Switch Package ContentsInsert Switch Blade and Power On Connect Console Installing and Configuring the SwitchInstalling the Switch Blade in a PowerEdge M1000e After you slide the MXL 10/40GbE Switch in so that the connectors on the back of the blade touch the chassis midplane, the switch receives power from the chassis and automatically powers on. The chassis management controller CMC in the chassis validates that the switch blade is a supported I/O module before powering it on Page Performing the Initial Configuration Invoking the X-Loader and U-Boot CLIsInitial Configuration Procedure Sample Setup Wizard Session set up the initial SNMP version 2 account now To access the switch through any Management Interface you can This is the configuration information that has been collected Figure 1-9. Six Stacked MXL 10/40GbE Switches Assembling a Switch StackConfiguring and Bringing Up a Stack 2 Save the stacking configuration on the 40GbE ports Topology Discovery Master and Member SwitchesManaging a Stack Stack StartupFTOS# upgrade system stack-unit 3 a Auto Stack Number AssignmentFTOS Version Checking FTOS# upgrade system stack-unit unit-number partitionSplitting 40GbE QSFP+ Ports into 10GbE SFP+ Ports System InitializationSwitch Configuration Switch ConfigurationiSCSI Operation DCB SupportFCoE Connectivity Next Steps Next StepsEnvironmental Parameters Technical SpecificationsChassis Physical Design IEEE Standards Power RequirementsTechnical Specifications Page Printed in the U.S.A w w w. d e l l . c o m s u p p o r t . d e l l . c o m