Manuals / Fortinet / Computer Equipment / Network Card

Fortinet 5001A-SW, 5001A-DW manual Hardware installation, Quick Configuration Guide, Contents

Models: 5001A-SW 5001A-DW

1 40

Download 40 pages 49.38 Kb

Page 3

Contents

Contents

Contents
Warnings and cautions	2
FortiGate-5001A security system	5
Front panel LEDs and connectors	6
LEDs	7
Connectors	8
Base backplane communication	8
Fabric backplane communication	8
FortiGate-RTM-XB2	9
AMC modules	9
Hardware installation	11
Changing FortiGate-5001A SW11 switch settings	12
FortiGate-5001A mounting components	14
Inserting a FortiGate-5001A board	15
Removing a FortiGate-5001A board	18
Resetting a FortiGate-5001A board	20
Installing and removing AMC modules	20
Inserting AMC slot filler panels	21
Inserting AMC modules	21
Removing AMC modules	22
Troubleshooting	23
FortiGate-5001A does not start up	23
FortiGate-5001A status LED is flashing during system operation	24
FortiGate AMC modules not detected by FortiGate-5001A board	24
Quick Configuration Guide	25
Registering your Fortinet product	25
Planning the configuration	25
NAT/Route mode	26
Transparent mode	26
Choosing the configuration tool	27
Web-based manager	27
Command Line Interface (CLI)	28
Factory default settings	28
Configuring NAT/Route mode	28
Using the web-based manager to configure NAT/Route mode	29
Using the CLI to configure NAT/Route mode	30

FortiGate-5001A Security System Guide
01-30000-83456-20081023	3

Image 3

Fortinet 5001A-SW, 5001A-DW Hardware installation, Quick Configuration Guide, Contents, FortiGate-5001A security system

Contents

FortiGate-5001A-SW Security System GuideFortiGate-5001A FortiGate-5001A-DWWarnings and cautions FortiGate-5001A status LED is flashing during system operation Hardware installationQuick Configuration Guide Using the web-based manager to configure NAT/Route modePowering off the FortiGate-5001A board Configuring Transparent modeUsing the web-based manager to configure Transparent mode Using the CLI to configure Transparent modeFortiGate-5001A security system Front panel LEDs and connectors FortiGate-5001A Security System Guide LEDsTable 1 lists and describes the FortiGate-5001A LEDs FortiGate-5001A security systemConnectors Base backplane communicationFabric backplane communication FortiGate-RTM-XB2 AMC modulesASM-FB4 Figure 5 FortiGate-ASM-FB4Installing and removing AMC modules Troubleshooting Hardware installationChanging FortiGate-5001A SW11 switch settings Removing a FortiGate-5001A board Resetting a FortiGate-5001A boardSW11 Changing FortiGate-5001A SW11 switch settingsFactory Default Shelf Manager Required Standalone Mode for FortiGate-5020 no Shelf ManagerTo change or verify the SW11 switch setting Location of SWFortiGate-5001A boardtop view FortiGate-5001A Front Faceplate FortiGate-5001A mounting components Figure 9 FortiGate-5001A right bottom mounting components ClosedOpen To insert a FortiGate-5001A board into a chassis slot Inserting a FortiGate-5001A boardUnlock Handle Alignment Pin Open Handle LockAlignment Pin Handle 9 Turn both handles to their fully-closed positions To remove a FortiGate-5001A board from a chassis slot Removing a FortiGate-5001A boardRemoving a FortiGate-5001A board Removing AMC modules Resetting a FortiGate-5001A boardInstalling and removing AMC modules Inserting AMC slot filler panels Inserting AMC modulesTo insert an AMC module into a FortiGate-5001A board To install an AMC slot filler panelInserting AMC slot filler panels Inserting AMC modulesTo remove an AMC module from a FortiGate-5001A board Removing AMC modulesChassis with a shelf manager no communication with shelf manager TroubleshootingAll chassis Firmware problem FortiGate-5001A does not start upTo remove and reset an AMC module FortiGate-5001A status LED is flashing during system operationFortiGate AMC modules not detected by FortiGate-5001A board Choosing the configuration tool Factory default settings Quick Configuration GuidePlanning the configuration Registering your Fortinet product Planning the configurationNAT/Route mode Transparent modeInternal Network Choosing the configuration tool Web-based managerInternal Network Factory default settings Configuring NAT/Route modeCommand Line Interface CLI To configure interfaces 1 Go to System Network Interface Using the web-based manager to configure NAT/Route modeTo change the admin administrator password 1 Go to System Admin Administrators1 Go to System Network Options Using the CLI to configure NAT/Route modeTo configure the Primary and Secondary DNS server IP addresses To configure the Default GatewayUsing the web-based manager to configure Transparent mode Configuring Transparent modeTo change the admin administrator password Using the CLI to configure Transparent modeTo switch from NAT/Route mode to transparent mode To change the management interface 1 Go to System Config OperationUpgrading FortiGate-5001A firmware To upgrade the firmware using the web-based manager4 Under System Information Firmware Version, select Update To upgrade the firmware using the CLIFortiGate-5001A base backplane data communication To enable base backplane data communication from the FortiGate-5001A config system global set show-backplane-intf enable end1 Go to System Network Interface 1 Go to System Network Interface FortiGate-5001A fabric backplane data communicationFortiGate-5001A board is to remove and reinsert it Powering off the FortiGate-5001A boardTo enable sending heartbeat packets to the FortiSwitch-5003A To power off a FortiGate-5001A board01-30000-83456-20081023 Powering off the FortiGate-5001A boardQuick Configuration Guide FortiGate-5001A Security System GuideRegister your Fortinet product Customer service and technical supportFor more information Fortinet documentationRegulatory compliance Trademarks