The fryer flue opening must not be placed close to the intake of the exhaust fan, and the fryer must never have its flue extended in a “chimney” fashion. An extended flue will change the combustion characteristics of the fryer, causing longer recovery time. It also frequently causes delayed ignition. To provide the airflow necessary for good combustion and burner operation, the areas surrounding the fryer front, sides, and rear must be kept clear and unobstructed.

DANGER

This appliance must be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to the health of personnel in the room in which it is installed.

Fryers must be installed in an area with an adequate air supply and adequate ventilation. Adequate distances must be maintained from the flue outlet of the fryer to the lower edge of the ventilation filter bank. Filters should be installed at an angle of 45º. Place a drip tray beneath the lowest edge of the filter. For U.S. installation, NFPA standard No. 96 states, “A minimum distance of 18 in. (450 mm) should be maintained between the flue outlet and the lower edge of the grease filter.” Frymaster recommends that the minimum distance be 24 in. (600 mm) from the flue outlet to the bottom edge of the filter when the appliance consumes more than 120,000 BTU per hour.

For installations in the United States, information on construction and installation of ventilating hoods can be found in the NFPA standard cited above. A copy of the standard may be obtained from the National Fire Protection Association, Battery March Park, Quincy, MA 02269.

2.1.2 National Code Requirements

The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of the fryer door. Connect a fryer stamped “NAT” only to natural gas, those stamped “PRO” only to propane gas, and those stamped “MFG” only to manufactured gas.

Installation shall be made with a gas connector that complies with national and local codes, and, where applicable, CE codes. Quick-disconnect devices, if used, shall likewise comply with national, local, and, if applicable, CE codes. In the absence of local codes, installation must conform to the national Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Natural Gas and Propane Installation code, CSA B149.1, as applicable including:

1.The appliance and its individual shutoff valve must be disconnected form the gas supply piping system during any pressure testing of the system at test pressures in excess of ½ psi (3.5 kPa).

2.The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at trest pressures equal to or less than ½ psi (3.5 kPa).

2.1.3 Electrical Grounding Requirements

All electrically operated appliances must be grounded in accordance with all applicable national and local codes, and, where applicable, CE codes. In the absence of local codes, the appliance must be grounded in accordance with National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable. All units (cord connected or permanently connected) should be connected to a grounded power supply system. A wiring diagram is located on the inside of the fryer door. Refer to the rating plate on the inside of the fryer door for proper voltages.

2-2

Page 11
Image 11
Frymaster BIGLA30 warranty National Code Requirements, Electrical Grounding Requirements

BIGLA30 specifications

The Frymaster BIGLA30 is a state-of-the-art commercial frying solution designed to meet the high demands of busy food service environments. Known for its energy efficiency, reliability, and advanced technology, the BIGLA30 has become a favorite among restaurateurs and catering businesses.

One of the standout features of the BIGLA30 is its large capacity. With a significant oil capacity, it allows for frying large quantities of food simultaneously, making it ideal for high-volume establishments. This capacity enables kitchens to keep up with demand during peak hours, ensuring that orders are fulfilled quickly and efficiently.

The Frymaster BIGLA30 is equipped with advanced digital controls that simplify the frying process. The intuitive interface allows operators to easily adjust cooking times and temperatures, ensuring consistent results. The digital controls are also equipped with a filtration system that automatically cleans the oil, which prolongs its life and ensures the food maintains optimal flavor.

Another prominent feature of the BIGLA30 is its energy-efficient design. It utilizes innovative heating technology that reduces energy consumption while providing high-performance frying. This not only helps to lower operational costs but also supports environmentally friendly practices within the kitchen.

Safety is paramount in any commercial kitchen, and the BIGLA30 excels in this area. It is designed with safety mechanisms such as automatic shut-off and temperature control systems to prevent overheating. Additionally, the unit features large, easy-to-grip handles on pots, allowing for safe handling and transfer of food items.

In terms of construction, the Frymaster BIGLA30 is built with high-quality materials that ensure durability and longevity. The robust design can withstand the rigors of a busy kitchen and is easy to maintain, reducing downtime and service costs. Its sleek stainless-steel exterior not only presents a professional aesthetic but is also simple to clean, contributing to overall kitchen hygiene.

Furthermore, the BIGLA30 is compatible with various cooking applications, making it versatile enough to fry a wide range of items from crispy fries to delicious chicken. This adaptability makes it a valuable addition to any food service operation.

In summary, the Frymaster BIGLA30 is a top-tier frying solution that combines capacity, energy efficiency, advanced technology, and safety features. Its ability to deliver consistent results while minimizing costs makes it an essential tool for any commercial kitchen.