Fujitsu M3093DE/DG specs

Edition	Date published	Revised contents
01	September,1996	First edition

Specification No. C150-E071-01EN

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This digital apparatus does not exceed the Class A limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications.

Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescridtes dans le Réglesment sur le brouillage radioélectrique dicté par le ministere des Communi- cations du Canada.

MaschinenlärmInformationsverordnung 3. GSGV, 18.01.1991:Der arbeisplatzbe- zogene Schalldruckpegel beträgt 70dB(A)oder weniger gemäß ISO 7779.

The contents of this manual may be revised without prior notice.

All Rights Reserved, Copyright © 1996 FUJITSU LIMITED. Printed in Japan.

No part of this manual may be reproduced in any form without permission.

Image 3

Fujitsu M3093DE/DG manual

Contents

M3093DE/DG Image Scanner Page Page Fujitsu Australia Limited Important Note to Users Preface Conventions Page Contents Page Description Operating Instruction Page Description Units No. Function Assemblies Guide aRetaining Thumb screw Spring Consumables Bearing Indicators Power Read CheckPower Page Operating Instruction Lift up the ADF lever to open Loading Document on the ADF It clicks Set the paper select lever as FollowsClose the ADF Pull up the ADF paper chute until Fan the sheets before setting Document on the ADF paperChute Angle the document edges as follows Documents Guide lever Both sides Loading Document on the Flatbed Loading Document Larger than the Document Board Reading a Page from a Thick Book Page Cleaning Supplies Cleaning Supplies and Cleaning Area Flatbed Cleaning area Cleaning the ADF Remove dirt and dust as follows Lift up the ADF lever to open the ADF Pick roller Sheet guide white part Wipe the sheet guide Wipe the Plastic roller Cleaner F2Surface with clean and dry Moisten a cotton swab with Allow to dry Cleaning the FlatbedApply Cleaner F1 to a clean cloth Wipe the document holding pad Replacement of Parts Slide the pad ASY to the left Pad ASY or PadSlide the paper select Lever to N Attach the pad ASY to the ADF Until it clicks in the reverseSequence of step Lift up the ADF lever to open Remove the two thumb screws Pick Roller Lift and remove it Slide the pick roller to the retainingSpring side until the axis Opposite side is disengaged New roller Attach the retaining spring to a Attach the Guide a in the reverse Sequence of and alignScrew hole Tighten the thumb screws Close the ADF unit Page Troubleshooting Close the ADF until the ADF lever Paper JAMRemove the documents from ADF paper chute Contact manufacturer’s authorized service center Connect the power cable correctly Press the power switchInitial Checks Are the documents loaded on the ADF Is the baud rate System 4800 bps? Default is 4800 bps Is halftone or dithering processing selected? Host computer Select a Line Art mode fromSelect the Photo mode White level following off Clean the dirty parts Is the surface of the ADF Check Flatbed to read the document Clean the pick rollerClean or replace the Pad ASY Flatten the curl or use Do not mix different width documents Symptom8 Paper double feed occurs frequently Is the height of document less than 0.16 4mm? Install it correctly See p4-2 Flatten the curl or use the flatbed to read the documentSet the select lever to T. See p2-3 Replace the pick roller. See p4-4 Clean the pick roller. See p3-4, p3-6 YES Test Mode for Maintenance LED status on error General Problem Checklist