Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093DE/DG manual Contact manufacturer’s authorized service center, Yes Yes

Models: M3093DE/DG

1 65

Download 65 pages 12.93 Kb

Page 61

Clean the ADF (See p3-4) or remove the foreign particles.

Symptom10 Paper jam occurs frequently.

Does the condition of the document satisfy the requirements on page 5-11.

NO

Is there any foreign particles in the ADF?

NO

Contact manufacturer’s authorized service center.

YES

YES

Flatten the curl or use the flatbed to read the document.

Clean the ADF (See p3-4) or remove the foreign particles.

5-16

Image 61

Fujitsu M3093DE/DG manual Contact manufacturer’s authorized service center, Yes Yes

Contents

M3093DE/DG Image Scanner Cleaning and MaintenanceC150-E071-01EN Page Specification No. C150-E071-01EN Revised contentsThe contents of this manual may be revised without prior notice EditionFUJITSU COMPUTER PRODUCTS OF IMPORTANT NOTE TO USERS Refer to Operator’s Guide for basic information about the M3093DE/DG PrefaceConventions Page CHAPTER CONTENTSCHAPTER CHAPTERPage CHAPTER 3 CLEANING CHAPTER 4 REPLACEMENT OF PARTS CHAPTER 5 TROUBLESHOOTINGCLEANING REPLACEMENTPage DESCRIPTION Units Assemblies IndicatorsCHAPTER DESCRIPTIONUnits No. Function Assemblies LED functions IndicatorsPower Read Check PowerPage Loading Document on the ADF Loading Document on the Flatbed OPERATING INSTRUCTIONReading a Page from a Thick Book Loading Document Larger than the Document BoardLift up the ADF lever to open the 1 ADF Loading Document on the ADFClose the ADF Set the paper select lever as 2 followsPull up the ADF paper chute until it clicksthe document on the ADF paper Fan the sheets before settingchute Document6 Angle the document edges as follows Set the guides so that there is a Issue the read command Loading Document on the Flatbed1 Open the document cover Place the document faceLoading Document Larger than the Document Board Issue the read command from the Reading a Page from a Thick Book1 Open the document cover Place the book face-down on thePage Cleaning Supplies and Cleaning Area Cleaning the ADF CLEANINGCleaning the Flatbed CLEANINGSupplies Cleaning Supplies and Cleaning AreaSupplies Type NoCleaning paper Cleaning areawith Cleaner F1 with Cleaner F1Cleaning the ADF with cleaning paper Cleaning the ADFIf the glass is dirty, the image may include vertical stripes Cleaning the ADF with Dry cloth with Cleaner F1Feed rollers and Plastic rollers Pick roller Wipe the rollerWipe the rollers. Be careful not to damage the surface of the rollers Pick rollerSheet guide white part Wipe the sheet guide CLEANINGClose the ADF to lock the ADF lever O T ECleaner F2 Cleaning the Plastic rollers with Cleaner F2surface with clean and dry Lift up the ADF lever to openCleaning the Flatbed with Dry cloth with Cleaner F1 Cleaning the FlatbedApply Cleaner F1 to a clean cloth Window or glass cleaner can be used instead of cleaner F1Pad ASY or Pad Pick Roller REPLACEMENT OF PARTSREPLACEMENT CHAPTERLift up the ADF lever to open Pad ASY or Padthe ADF Slide the paper selectIf the Pad is attached to the scanner 4 you can replace the Pad according to the following procedureAttach the pad ASY to the ADF until it clicks in the reverseUse a Phillips screwdriver when they are tight Pick RollerLift up the ADF lever to open the 1 ADF Remove the two thumb screwsLift up the Guide A with both of Attach the retaining spring to a Attach the Guide A in the reverse REPLACEMENT OF PARTSsequence of step 3 and align the screw holePage Paper JAM Initial Checks Test Mode for Maintenance Problem Checklist TROUBLESHOOTINGTROUBLESHOOTING CHAPTERRemove the documents from Paper JAMthe ADF paper chute Lift the ADF lever to open the ADF Remove the jammed documentContact manufacturer’s authorized service center Initial ChecksConnect the power cable correctly Press the power switch TROUBLESHOOTINGPlace the carrier fixing bracket correctly See Operator’s Guide NO NOInsert the first few pages into the slot YES NORefer to Symptom See p5-9 Contact manufacturer’s authorized service centerConnect the terminator or set the SCSI ID correctly NO NO NO Symptom3 Pictures and photographs are not read correctlySelect the “Photo” mode Select a “Line Art” mode fromClean the dirty parts Contact manufacturer’s authorized service centermissing Place the carrier fixing bracket correctly. See Operator’s Guide TROUBLESHOOTINGClean or replace the Pad ASY Clean the pick rollerContact manufacturer’s authorized service center Flatten the curl or use theRemove paper clips and staples. Flatten the staple holes Flatten the curl or use the flatbed to read the document Clean the pad. See p3-4,p3-5 Replace the pad. See p4-2 Contact manufacturer’s authorized service centerTROUBLESHOOTING YES YESYES YES Symptom9 Miss pick occurs frequentlyClean the pick roller. See p3-4, p3-6 Contact manufacturer’s authorized service centerTROUBLESHOOTING Replace the pick roller. See p4-4Clean the ADF See p3-4 or remove the foreign particles Contact manufacturer’s authorized service centerYES YES Flatten the curl or use the flatbed to read the documentTest Mode for Maintenance Ending the test in ADF mode Ending the test in flatbed modeLED status on error Activating the continuous operation testTransport error Problem ChecklistImage error General