Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093DE/DG manual Cleaning Supplies and Cleaning Area

Models: M3093DE/DG

1 65

Download 65 pages 12.93 Kb

Page 30

Cleaning Supplies and Cleaning Area

Document cover

Document holding pad

Document bed

Supplies

Supplies	Type No.	Frequencies	(*1)	Remarks
Cleaning paper	Contact your	Every 5,000 sheets
	dealer or
Cleaner F2	distributer	• Plastic rollers	(*2)	1 bottle
				Apply Cleaner F2
				to cotton swab.
Cleaner F1 or		• PAD ASY		1 bottle.
Isopropyl alcohol		Every 5,000 sheets		Apply Cleaner F1
		• Pick roller/Feed rollers/		to cloth.
		Glass/Sheet guide
		Every 5,000 sheets
Cotton swab
Dry cloth

*1 When the CHECK indicator starts blinking at 4-second intervals, clean the scanner regardless of the frequencies.

*2 Clean the plastic rollers when they are soiled with dirt. Do not clean the rubber rollers with cleaner F2.

NOTE

When the following paper is used, it may be necessary to clean more frequently.

•Paper with smooth surface such as coated paper.

•Paper with almost all printed area.

•Paper with special coating such as carbon-less paper.

3-2

Image 30

Fujitsu M3093DE/DG manual Cleaning Supplies and Cleaning Area

Contents

M3093DE/DG Image Scanner Page Page Fujitsu Australia Limited Important Note to Users Preface Conventions Page Contents Page Description Operating Instruction Page Description Units No. Function Assemblies Guide aRetaining Thumb screw Spring Consumables Bearing Indicators Power Read CheckPower Page Operating Instruction Loading Document on the ADF Lift up the ADF lever to openPull up the ADF paper chute until Set the paper select lever as FollowsClose the ADF It clicksFan the sheets before setting Document on the ADF paperChute Angle the document edges as follows Documents Guide lever Both sides Loading Document on the Flatbed Loading Document Larger than the Document Board Reading a Page from a Thick Book Page Cleaning Cleaning Supplies and Cleaning Area SuppliesCleaning area FlatbedCleaning the ADF Lift up the ADF lever to open the ADF Remove dirt and dust as followsPick roller Sheet guide white part Wipe the sheet guide Moisten a cotton swab with Cleaner F2Surface with clean and dry Wipe the Plastic rollerWipe the document holding pad Cleaning the FlatbedApply Cleaner F1 to a clean cloth Allow to dryReplacement of Parts Lever to N Pad ASY or PadSlide the paper select Slide the pad ASY to the leftAttach the pad ASY to the ADF Until it clicks in the reverseSequence of step Pick Roller Lift up the ADF lever to open Remove the two thumb screwsOpposite side is disengaged Slide the pick roller to the retainingSpring side until the axis Lift and remove itAttach the retaining spring to a New rollerAttach the Guide a in the reverse Sequence of and alignScrew hole Tighten the thumb screws Close the ADF unit Page Troubleshooting ADF paper chute Paper JAMRemove the documents from Close the ADF until the ADF leverContact manufacturer’s authorized service center Connect the power cable correctly Press the power switchInitial Checks Are the documents loaded on the ADF Is the baud rate System 4800 bps? Default is 4800 bps Is halftone or dithering processing selected? Clean the dirty parts Select a Line Art mode fromSelect the Photo mode White level following off Host computerIs the surface of the ADF Check Flatten the curl or use Clean the pick rollerClean or replace the Pad ASY Flatbed to read the documentDo not mix different width documents Symptom8 Paper double feed occurs frequently Is the height of document less than 0.16 4mm? Install it correctly See p4-2 Flatten the curl or use the flatbed to read the documentSet the select lever to T. See p2-3 Clean the pick roller. See p3-4, p3-6 Replace the pick roller. See p4-4YES Test Mode for Maintenance LED status on error Problem Checklist General