Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093DE/DG Activating the continuous operation test, Ending the test in flatbed mode

Models: M3093DE/DG

1 65

Download 65 pages 12.93 Kb

Page 63

Activating the continuous operation test

Activating the continuous operation test

Open the ADF and close it again. If no document is loaded on the ADF within five seconds after closing the ADF, the image scanner runs in flatbed mode. If documents are loaded on the ADF within five seconds after closing the ADF, the image scanner continuously feeds the document from ADF. Once the image scanner starts reading documents in flatbed mode, it does not feed documents from ADF even if documents are loaded on the ADF.

Ending the test in flatbed mode

To stop the carrier movement in flatbed mode, open the ADF. If the ADF is opened, the POWER lamp starts blinking immediately after the carrier returns to the home position.

Ending the test in ADF mode

If the ADF hopper is empty, feeding documents from the ADF ends. To restart feeding, open the ADF and close it again. Then load documents on the ADF paper chute within five seconds after closing the ADF.

LED status on error

If an error occurs during the test, the LED indicates as shown in the following table.

Errors	Paper	Carrier	Front	Back	Motor	Lamp
Status	jam	unit	optical	optical	fuse	fuse
LED		error	system	system	failure	failure
indicates			error	error

Power

Read

Check

O T E				Blink		On	Off

5-18

Image 63

Fujitsu M3093DE/DG Activating the continuous operation test, Ending the test in flatbed mode, Ending the test in ADF mode

Contents

Cleaning and Maintenance M3093DE/DG Image ScannerC150-E071-01EN Page Edition Revised contentsSpecification No. C150-E071-01EN The contents of this manual may be revised without prior noticeFUJITSU COMPUTER PRODUCTS OF IMPORTANT NOTE TO USERS Refer to Operator’s Guide for basic information about the M3093DE/DG PrefaceConventions Page CHAPTER CONTENTSCHAPTER CHAPTERPage REPLACEMENT CHAPTER 4 REPLACEMENT OF PARTS CHAPTER 5 TROUBLESHOOTINGCHAPTER 3 CLEANING CLEANINGPage DESCRIPTION Units Assemblies IndicatorsDESCRIPTION CHAPTERUnits No. Function Assemblies Power IndicatorsLED functions Power Read CheckPage Loading Document Larger than the Document Board OPERATING INSTRUCTIONLoading Document on the ADF Loading Document on the Flatbed Reading a Page from a Thick BookLift up the ADF lever to open the 1 ADF Loading Document on the ADFit clicks Set the paper select lever as 2 followsClose the ADF Pull up the ADF paper chute untilDocument Fan the sheets before settingthe document on the ADF paper chute6 Angle the document edges as follows Set the guides so that there is a Place the document face Loading Document on the FlatbedIssue the read command 1 Open the document coverLoading Document Larger than the Document Board Place the book face-down on the Reading a Page from a Thick BookIssue the read command from the 1 Open the document coverPage CLEANING CLEANINGCleaning Supplies and Cleaning Area Cleaning the ADF Cleaning the FlatbedType No Cleaning Supplies and Cleaning AreaSupplies Supplieswith Cleaner F1 Cleaning areaCleaning paper with Cleaner F1Cleaning the ADF with cleaning paper Cleaning the ADFIf the glass is dirty, the image may include vertical stripes Cleaning the ADF with Dry cloth with Cleaner F1Pick roller Pick roller Wipe the rollerFeed rollers and Plastic rollers Wipe the rollers. Be careful not to damage the surface of the rollersO T E CLEANINGSheet guide white part Wipe the sheet guide Close the ADF to lock the ADF leverLift up the ADF lever to open Cleaning the Plastic rollers with Cleaner F2Cleaner F2 surface with clean and dryWindow or glass cleaner can be used instead of cleaner F1 Cleaning the FlatbedCleaning the Flatbed with Dry cloth with Cleaner F1 Apply Cleaner F1 to a clean clothCHAPTER REPLACEMENT OF PARTSPad ASY or Pad Pick Roller REPLACEMENTSlide the paper select Pad ASY or PadLift up the ADF lever to open the ADFuntil it clicks in the reverse 4 you can replace the Pad according to the following procedureIf the Pad is attached to the scanner Attach the pad ASY to the ADFRemove the two thumb screws Pick RollerUse a Phillips screwdriver when they are tight Lift up the ADF lever to open the 1 ADFLift up the Guide A with both of Attach the retaining spring to a screw hole REPLACEMENT OF PARTSAttach the Guide A in the reverse sequence of step 3 and align thePage CHAPTER TROUBLESHOOTINGPaper JAM Initial Checks Test Mode for Maintenance Problem Checklist TROUBLESHOOTINGLift the ADF lever to open the ADF Remove the jammed document Paper JAMRemove the documents from the ADF paper chuteTROUBLESHOOTING Initial ChecksContact manufacturer’s authorized service center Connect the power cable correctly Press the power switchYES NO NO NOPlace the carrier fixing bracket correctly See Operator’s Guide Insert the first few pages into the slotContact manufacturer’s authorized service center Refer to Symptom See p5-9Connect the terminator or set the SCSI ID correctly NO NO NO Symptom3 Pictures and photographs are not read correctlyContact manufacturer’s authorized service center Select a “Line Art” mode fromSelect the “Photo” mode Clean the dirty partsmissing Place the carrier fixing bracket correctly. See Operator’s Guide TROUBLESHOOTINGFlatten the curl or use the Clean the pick rollerClean or replace the Pad ASY Contact manufacturer’s authorized service centerRemove paper clips and staples. Flatten the staple holes Flatten the curl or use the flatbed to read the document YES YES Contact manufacturer’s authorized service centerClean the pad. See p3-4,p3-5 Replace the pad. See p4-2 TROUBLESHOOTINGYES YES Symptom9 Miss pick occurs frequentlyReplace the pick roller. See p4-4 Contact manufacturer’s authorized service centerClean the pick roller. See p3-4, p3-6 TROUBLESHOOTINGFlatten the curl or use the flatbed to read the document Contact manufacturer’s authorized service centerClean the ADF See p3-4 or remove the foreign particles YES YESTest Mode for Maintenance Activating the continuous operation test Ending the test in flatbed modeEnding the test in ADF mode LED status on errorGeneral Problem ChecklistTransport error Image error