Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MHV2040AT, MHV2100AT, MHV2080AT, MHV2120AT, MHV2060AT manual SET Multiple Mode X’C6’

Models: MHV2040AT MHV2100AT MHV2060AT MHV2080AT MHV2120AT

1 280

Download 280 pages 1.69 Kb

Page 143

5.3 Host Commands

(20) SET MULTIPLE MODE (X’C6’)

This command enables the device to perform the READ MULTIPLE and WRITE MULTIPLE commands. The block count (number of sectors in a block) for these commands is also specified by the SET MULTIPLE MODE command.

The number of sectors per block is written into the Sector Count register. The IDD supports 2, 4, 8, 16 and 32 (sectors) as the block counts.

Upon receipt of this command, the device sets the BSY bit of the Status register and checks the contents of the Sector Count register. If the contents of the Sector Count register are valid and are supported block count, the value is stored for all subsequent READ MULTIPLE and WRITE MULTIPLE commands. Execution of these commands is then enabled. If the value of the Sector Count register is not a supported block count, an ABORTED COMMAND error is posted and the READ MULTIPLE and WRITE MULTIPLE commands are disabled.

If the contents of the Sector Count register is 0, when the SET MULTIPLE MODE command is issued, the READ MULTIPLE and WRITE MULTIPLE commands are disabled.

When the SET MULTIPLE MODE command operation is completed, the device clears the BSY bit and generates an interrupt.

At command issuance (I/O registers setting contents)

1F7H(CM)	1	1	0	0	0	1	1	0

1F6H(DH)	x	x	x	DV	xx
1F5H(CH)	xx
1F4H(CL)	xx
1F3H(SN)	xx
1F2H(SC)	Sector count/block
1F1H(FR)	xx

After power-on the READ MULTIPLE and WRITE MULTIPLE command operation are disabled as the default mode.

C141-E218

5-67

Image 143

Fujitsu MHV2040AT, MHV2100AT, MHV2080AT, MHV2120AT, MHV2060AT manual SET Multiple Mode X’C6’

Contents

Disk Drive Product Manual MHV2120AT, MHV2100AT, MHV2080AT MHV2060AT, MHV2040AT Handling of This Manual For Safe Operation Revision History This page is intentionally left blank Overview of Manual Preface Conventions Conventions for Alert MessagesOperating Environment Liability Exception This page is intentionally left blank Damage Interface cable connection Important Alert ItemsImportant Alert Messages This page is intentionally left blank Disk Drive Product Manual Disk Drive Maintenance ManualManual Organization This page is intentionally left blank Contents Theory of Device Operation Installation Conditions Interface Contents 101 Write Multiple EXT X’39’ Option customizing Operations Glossary GL-1 Acronyms and Abbreviations AB-1 Index IN-1 Figures Illustrations Execution example of Read Multiple command Tables Surface temperature measurement points and standard 25 Relationship between combination of Identifier This page is intentionally left blank Device Overview Adaptability FeaturesFunctions and performance Data buffer Error correction and retry by ECCHigh resistance against shock Connection to ATA interface Specifications 1 Device SpecificationsSpecifications summary Examples of model names and product numbers Specifications 2Model and product number Ripple Power RequirementsInput Voltage Current and power dissipation Current Requirements and Power Dissipation Environmental specifications Environmental SpecificationsCurrent fluctuation Typ. at +5 V when power is turned on Power on/off sequence Shock and Vibration Acoustic noise specificationShock and vibration specification Acoustic Noise Mean time between failures Mtbf Service lifeData assurance in the event of power failure Reliability Media Defects Error RateUnrecoverable read error Positioning error Advanced Power Management Advanced Power Management Advanced Power Management This page is intentionally left blank Device Configuration Device Configuration Read/write circuit System ConfigurationATA interface 2 1 drive connection 3 2 drives connection 2 drives configuration Installation Conditions Dimensions Dimensions Orientation MountingIntegration Guidance C141-E144 PCA FrameLimitation of mounting Location of breather Ambient temperature Handling cautions Service area Handling cautions Cable Connections Device connector FCI Cable connector specificationsCable connector specifications Device connection Location of setting jumpers Jumper SettingsPower supply connector CN1 Master drive-slave drive setting Factory default setting 14 Csel setting Csel setting 16 Example 2 of cable select Power up in standby setting Theory of Device Operation Spindle OutlineSubassemblies Disk Spindle motor driver circuit Circuit ConfigurationAir filter Servo circuit Power supply configuration PCA Power-on operation sequence Power-on Sequence Self-calibration Self-calibration contents Execution timing of self-calibration Command processing during self-calibration Write precompensation Read/write CircuitRead/write preamplifier PreAMP Write circuit Programmable filter circuit Read circuitAGC circuit Viterbi detection circuit Digital PLL circuitFIR circuit D converter circuit Servo control circuit Servo Control A converter DAC Power amplifierMicroprocessor unit MPU Servo burst capture circuit VCM current sense resistor CSR Driver circuit Outer guard band Data-surface servo formatInner guard band Data area Physical sector servo configuration on disk surface Servo frame format Track following operation Actuator motor controlOperation to move the head to the reference cylinder Seek operation Spindle motor control Start modeAcceleration mode Stable rotation mode This page is intentionally left blank Interface Physical Interface Interface signals Dasp GND Signal assignment on the connectorSignal assignment on the interface connector DA1 PDIAG-, Cblid DA0 DA2 Dior MstrDiow Stop Iordy PdiagCblid Dasp Logical Interface DA2 DA1 DA0 1 I/O registersI/O registers UNC Idnf Command block registersError register X’1F1’ Data register X’1F0’ Sector Count register X’1F2’ Features register X’1F1’SET Multiple Mode Cylinder High register X’1F5’ Sector Number register X’1F3’Cylinder Low register X’1F4’ BSY Device/Head register X’1F6’DEV HS3 HS2 HS1 HS0 Status register X’1F7’ Interface Alternate Status register X’3F6’ Command register X’1F7’Control block registers HOB Srst Host CommandsCommand code and parameters Device Control register X’3F6’ Parameter Used Command code and parameters 1 EXT Write Multiple FUA EXT Flush Cache EXT Command code and parameters 2 Host Commands Command descriptions Host Commands Recalibrate X’10’ to X’1F’ MSB Read Sectors X’20’ or X’21’ End head No. / LBA MSB Write Sectors X’30’ or X’31’ 1F7HST Status information 1F6HDH Write Verify X’3C’ Read Verify Sectors X’40’ or X’41’ Seek X’70’ to X’7F’ Diagnostic code Execute Device Diagnostic X’90’ Host Commands Initialize Device Parameters X’91’ Download Microcode X’92’ Operation of Download Microcode Standby Immediate X’94’ or X’E0’ Unload Feature Unload Immediate Command Host Commands Standby X’96’ or X’E2’ Idle X’97’ or X’E3’ Interface ’FF’ Check Power Mode X’98’ or X’E5’ Sleep X’99’ or X’E6’ Smart X’B0 Features register values subcommands and functions 1 Smart Read LOG Features register values subcommands and functions 2Smart Enable Operations Smart Disable Operations Smart Return Status Features register values subcommands and functions 3’DB’ Smart ENABLE/DISABLE Auto OFF-LINE Host Commands Format of insurance failure threshold value data Format of device attribute value data1FF Attribute ID Data format version number Raw attribute value Status FlagCurrent attribute value Attribute value for the worst case so far 11 Self-test execution status 10 Off-line data collection statusSelf-test execution status 13 Failure prediction capability flag Off-line data collection capability12 Off-line data collection capability Failure prediction capability flag Insurance failure threshold Error logging capability14 Error logging capability Check sum Smart error logging 16 Data format of Smart Summary Error Log 17 Data format of Smart Comprehensive Error Log Command data structureError data structure Total number of drive errors Self-test number Smart self-test18 Smart self-test log data format 1FC Current span under test 19 Selective self-test log data structureTest span Current LBA under test Selective self-test pending time min Feature flags20 Selective self-test feature flags Device Configuration Identify Device Configuration XB1Device Configuration Restore Device Configuration Freeze Device Configuration SET FR = C3h Device Configuration Restore FR = C0hDevice Configuration Freeze Lock FR = C1h Device Configuration Identify FR = C2h Interface 21 Device Configuration Identify data structure Interface Read Multiple X’C4’ Execution example of Read Multiple command MSB Write Multiple X’C5’ Interface SET Multiple Mode X’C6’ Interface Read DMA X’C8’ or X’C9’ End head No. / LBA MSB Write DMA X’CA’ or X’CB’ Interface Read Buffer X’E4’ Flush Cache X’E7’ Write Buffer X’E8’ Identify Device X’EC’ Identify Device DMA X’EE’ ’3FFF’ 22 Information to be read by Identify Device command 1 22 Information to be read by Identify Device command 2 Word Command without interrupt supports 2, 4, 8 and 16 sectors = Supports the Host Protected Area feature set = Supports the CFA Compact Flash Association feature set Interface Host Commands Interface Host Commands Word Bit Reserved Security level High, 1 Maximum ’CC’ SET Features X’EF’23 Features register values and settable modes ’BB’ Data Transfer Mode Advanced Power Management APM Automatic Acoustic Management AAM 24 Contents of Security SET Password data At command issuance I-O register contents 1F7hCM Security UNLOCKX’F2’ When the master password is selectedWhen the user password is selected Interface Security Erase Prepare X’F3’ Security Erase Unit X’F4’ Security Freeze Lock X’F5’ At command issuance I-O register contents 1F7hCM 26 Contents of security password Interface Read Native MAX Address X’F8’ SET MAX Address SET MAX X’F9’ SET MAX SET Password FR = 01h SET MAX Lock FR = 02h SET MAX Unlock FR = 03h SET MAX Freeze Lock FR = 04h Host Commands Read Sectors EXT X’24’ Option customizing Description Read DMA EXT X’25’ Option customizing Description Error reporting conditions Read Multiple EXT X’29’ Option customizing Description Read LOG EXT X2F Optional command Customize Description Host Commands Write Sectors EXT X’34’ Option customizing Description Write DMA EXT X’35’ Option customizing Description SET MAX Address EXT X’37’ Option customizing Description SET MAX LBA Write Multiple EXT X’39’ Option customizing Description Write DMA FUA EXT X’3D’ Option customizing Description Write LOG EXT X’3F’ Optional command Customize Description Host Commands Read Verify Sectors EXT X’42 Option customizing Description Write Multiple FUA EXT X’CE’ Option customizing Description Flush Cache EXT X’EA’ Option customizing Description 27 Command code and parameters 1 Error posting 27 Command code and parameters 2 Execute Device Diagnostic Initialize Device Parameters Command ProtocolPIO Data transferring commands from device to host Read Sectors Command protocol Protocol for command abort PIO Data transferring commands from host to device Write Sectors command protocol Commands without data transfer Read DMA EXT Write DMA EXT/FUA EXT Indentify Device DMA Other commandsDMA data transfer commands Read Multiple EXT Write Multiple EXT/FUA EXT Sleep Normal DMA data transfer Overview Ultra DMA Feature Set Initiating an Ultra DMA data in burst Phases of operationUltra DMA data in commands Data in transfer Pausing an Ultra DMA data in burst Terminating an Ultra DMA data in burst Ultra DMA Feature Set Interface Initiating an Ultra DMA data out burst Ultra DMA data out commands Data out transfer Pausing an Ultra DMA data out burst Terminating an Ultra DMA data out burst Interface Ultra DMA CRC rules DIOW-STOP Series termination required for Ultra DMA28 Recommended series termination for Ultra DMA DIOR-HDMARDY-HSTROBE PIO data transfer timing TimingPIO data transfer Multiword data transfer 10 Multiword DMA data transfer timing mode 11 Initiating an Ultra DMA data in burst Ultra DMA data transfer Strobe Name Mode Comment MIN MAX 29 Ultra DMA data burst timing requirements 2 30 Ultra DMA sender and recipient timing requirements Mode Name Comment DD150 at host Sustained Ultra DMA data in burstDstrobe at device DD150 at device Dstrobe at host Hdmardy Host pausing an Ultra DMA data in burstDmarq Dmack Stop Device terminating an Ultra DMA data in burst DA0, DA1, DA2 CS0, CS1 Host terminating an Ultra DMA data in burstHost 16 Initiating an Ultra DMA data out burst Hstrobe at device DD150 at device Sustained Ultra DMA data out burstHstrobe at host DD150 at host Hstrobe host DD150 Host Device pausing an Ultra DMA data out burstDevice DMACK- host Stop host DDMARDY- device 19 Host terminating an Ultra DMA data out burst Host terminating an Ultra DMA data out burst DD150 Host Device terminating an Ultra DMA data out burstDmarq device DMACK- host Only master device is present Power-on and resetMaster and slave devices are present 2-drives configuration Operations Response to power-on Device Response to the Reset Response to power-on Response to hardware reset Response to hardware reset Response to software reset Response to software reset Response to diagnostic command Response to diagnostic command Active idle mode Power SavePower save mode Active mode Sleep mode Standby mode Spare area Power commandsDefect Processing Track slip processing Alternating processing for defective sectorsSector slip processing Automatic alternating processing Automatic alternating processing 8MB buffer 8,388,608 bytes Read-ahead CacheData buffer structure Invalidating caching-target data Commands that are targets of cachingCaching operation Data that is a target of caching Smart Miss-hit Using the read segment buffer Sequential hit Full hit Partial hit Invalidation of cached data Command that are targets of cachingWrite Cache Cache operation Enabling and disabling Status report in the event of an errorReset response Caching function when power supply is turned on Write Cache This page is intentionally left blank Glossary Positioning Power save modeRotational delay PIO Programmed input-output VCM Status This page is intentionally left blank Acronyms and Abbreviations This page is intentionally left blank AAM Index Index Host terminating ultra DMA data Read Native MAX Address Read Sectors Command Surface temperature measurement This page is intentionally left blank Japan Comment Form This page is intentionally left blank C141-E218-01EN MHV2120AT, MHV2100AT, MHV2080AT, MHV2060AT, MHV2040AT This page is intentionally left blank