Manuals / Fujitsu / Computer Equipment / Server

Fujitsu TX150 S3 manual Introduction, Additional accessible drives, Hard disks extension box

Models: TX150 S3

1 95

Download 95 pages 1.83 Kb

Page 11

Introduction

Introduction

Extensions and conversions

Additional accessible drives

Three 5.25-inch bays are available for accessible drives. The top side bay is already occupied by a CD/DVD ROM drive.

Hard disks extension box

In the SCSI version the two lower 5.25-inch bays for accessible drives can be used to integrate a hard disks extension box.

The hard disks extension box enables up to three additional HDD modules to be integrated. Each HDD module can accommodate a SCSI hard disk drive with an SCA (Single Connector Attachment) interface and a height of at most 1 inch. The connection to the SCSI backplane is made without cables via the SCA interface. This makes it simple to plug in or pull out the HDD modules. If the server has a RAID controller and the corresponding RAID configuration, defective HDD modules can also be replaced while the system is operating.

Additional controllers in the PCI slots

The system board offers six PCI slots: 2 x PCI-X (64 Bit / 66 MHz), 3 x PCI (32 Bit / 33 MHz) and 1 x PCI-Express x1 slot.

The PCI slot 2 is prepared for Zero Channel RAID (ZCR).

RemoteView Service Board S2 LP

The RemoteView Service Board S2 LP (RSB S2 LP) is a PCI board with a completely independent system, i.e. it has its own operating system with Web server and SNMP agents and can optionally be equipped with an external power supply. The RSB S2 LP permits remote diagnosis for system analysis, remote system configuration and remote restart even in the event of operating system failure or hardware faults. It has its own LAN connection and its own COM port. All the functions of the RSB S2 LP are thus available either via a LAN or modem.

External SCSI interface

If the internal hard disks are connected via a PCI RAID controller, one channel of the on-board controller can also be made available for connecting a peripheral cabinet SX10 via an external SCSI interface.

U41604-Z156-1-76

Options Guide

3

Image 11

Fujitsu TX150 S3 Introduction, Additional accessible drives, Hard disks extension box, RemoteView Service Board S2 LP

Contents

Options Guide PRIMERGY TX150 S3 Server SystemCertified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks External SCSI interface Conversion standard PS to hot-plug PS ContinuedIntroduction Procedure Safety notes Preparation Main memory Accessible drives Controller in the PCI slots RemoteView componentsPage Appendix Abbreviations, Related publications and Index Converting from the floorstand model to the rack model CompletionPage PCI slot assembling ContentsRemoteView Service Board S2 LP Installing the external SCSI interfaceContents Additional documentation about the server 1 Introduction1.1 Overview of the documentation Concept and target groupsFurther sources of information 1.2 Extensions and conversionsExtensions and conversions Reklamat-PC-LOG@fujitsu-siemens.comAdditional controllers in the PCI slots Additional accessible drivesIntroduction Hard disks extension boxConversion of the floorstand model to a rack model Conversion standard power supply to hot-plug power supply1.3 Notational conventions Notational conventionsV CAUTION 2 ProcedurePage V CAUTION 3 Safety notesBefore operating the device V CAUTION V CAUTION Safety notesInstallation and operation V CAUTION V CAUTION Safety notesSafety notes Batteries V CAUTIONV CAUTION Safety notes Notes on handling CDs and CD-/DVD-ROM drives V CAUTIONNever remove parts of the CD-/DVD-ROM drive assembly Note about the laserFigure 1 ESD label Modules with electrostatic-sensitive componentsSafety notes V CAUTION 4 Preparation4.1 Floorstand model 4.1.1 Opening the serverFloorstand model 4.1.2 Removing the front coverPreparation 4.1.3 Removing the hard disk coverRack model 4.2 Rack model4.2.1 Opening the server Figure 8 Removing the server from the rack cabinet Rack modelPreparation Figure 7 Loosening the locking springFigure 9 Loosening the screws Rack modelV CAUTION PreparationRack model 4.2.2 Removing the rack front coverPreparation Page V CAUTION 5 Main memory5.1 Equipping rules Extending/replacing the main memory 5.2 Extending/replacing the main memoryExtending/replacing the main memory Main memoryPage V CAUTION 6 Accessible drives6.1 Installing an accessible 5.25-inch drive Figure 16 Attaching the EasyClick rails - DVD-ROM burner Installing an accessible 5.25-inch driveAccessible drives V CAUTIONInstalling an accessible 5.25-inch drive Accessible drivesFigure 19 Attaching the EasyClick rails - magnetic tape drive VXA-2 Installing an accessible 5.25-inch driveAccessible drives V CAUTION 6.2 Installing the hard disks extension boxAccessible drives Installing the hard disks extension boxAccessible drives Installing the hard disks extension boxPCIe Slot PCI Slot PCI Slot PCI Slot PCI Slot PCI Slot 7 Controller in the PCI slotsV CAUTION Controller in the PCI slots 7.1 Installing a controllerInstalling a controller V CAUTIONInstalling a controller Controller in the PCI slotsController in the PCI slots 7.2 PCI slot assemblingPCI slot assembling V CAUTION 8.1 RemoteView Service Board S2 LP8 RemoteView components RemoteView components RemoteView Service Board S2 LPFigure 25 Connecting cables to the RSB S2 LP Figure 26 Connecting cables to the system boardRemoteView components RSB S2 LPRemoteView Service Board S2 LP Figure 27 Connecting external cablesRemoteView Service Board S2 LP V CAUTION 9.1 Installing the external SCSI interface9 External SCSI interface Page V CAUTION 10 Conversion standard PS to hot- plug PSV CAUTION Figure 29 Loosening the screws Figure 30 Taking out the standard power supplyConversion standard PS to hot-plug PS Conversion standard PS to hot-plug PS Ê Insert the Power backplane in the PS cageÊ Fasten the Power backplane with one knurled screw see the circle Figure 31 Installing the Power backplane in the PS cageV CAUTION Figure 32 Installing the PS cageConversion standard PS to hot-plug PS U41604-Z156-1-76 Figure 33 Fastening the PS cage in the housingConversion standard PS to hot-plug PS Options GuideFigure 34 Fastening the PS cage at the rear side Conversion standard PS to hot-plug PSConversion standard PS to hot-plug PS Conversion standard PS to hot-plug PS Figure 36 Locking the power supply moduleV CAUTION Conversion standard PS to hot-plug PSFigure 38 Mounting the anti-tilt bracket Mounting the anti-tilt bracket only floorstand modelConversion standard PS to hot-plug PS V CAUTION Conversion standard PS to hot-plug PSPage V CAUTION 11 Converting from the floorstand model to the rack modelFigure 42 Removing the right-hand side cover Converting from the floorstand model to the rack modelFigure 41 Removing the screws V CAUTION Converting from the floorstand model to the rack modelConverting from the floorstand model to the rack model Figure 44 Installing the operating panel moduleU41604-Z156-1-76 Converting from the floorstand model to the rack modelPage V CAUTION 12 Completion12.1 Floorstand model 12.1.1 Attaching the hard disk coverCompletion 12.1.2 Attaching the front coverFloorstand model Completion 12.1.3 Closing the serverRack model 12.2 Rack model12.2.1 Attaching the rack front cover Ê Attach the rack front cover from the front Ê Attach the rack front cover using two screws on each sideCompletion Rack modelFigure 51 Attaching the top cover 12.2.2 Closing the serverRack model CompletionV CAUTION CompletionFigure 53 Fastening the server in the rack cabinet Rack modelCompletion 1-channel SCSI version with onboard SCSI controller 13 Appendix13.1 Cabling 13.1.1 SCSI versionData PowerSCSI IDE/FDIDE/FD CablingPower SCSIFigure 56 Cabling hard disk extension box Power SCSICabling IDE/FD Data Cable prefix T26139Options Guide 1.132 SATA versionPower CablingPage ASR&R BIOSAbbreviations ANSIEEPROM AbbreviationsIOOP Abbreviations HDDRTDS NVRAMPOST RAIDSDRAM Abbreviations SCASCSI SDDCPage 4 DataCenter Rack Technical Manual 5 19 inch rack Technical Manual 1 Safety 2 Warranty 3 PRIMECENTER Rack Technical Manual12 System Board D1979 Technical Manual 13 BIOS-Setup Reference Manual Related publications14 Integrated Mirroring User’s Guide 15 Global Array Manager Client Software User’s Guide 16 ConfiguratorRelated Publications Index Page Submitted by Comments on PRIMERGY TX150 S3 Server System Comments Suggestions CorrectionsFujitsu Siemens Computers GmbH User Documentation 81730 München GermanyPage Submitted by Comments on PRIMERGY TX150 S3 Server System Comments Suggestions CorrectionsFujitsu Siemens Computers GmbH User Documentation 81730 München GermanyPage http//ts.fujitsu.com Information on this documentHinweise zum vorliegenden Dokument