Manuals / Fujitsu / Computer Equipment / Server

Fujitsu TX150 S3 manual Completion, V Caution

Models: TX150 S3

1 95

Download 95 pages 1.83 Kb

Page 73

Image 73

Completion

Rack model

If you have not removed the server from the rack cabinet, please skip this page.

VCAUTION!

At least two people are required to install the server in the rack cabinet. Do not use the handles on the rack front cover to lift the server into the rack.

ÊLower the server from above onto the extended telescopic rails.

Figure 52: Installing the server in a rack cabinet

ÊScrew the telescopic rails onto the left-hand side (one screw) and right-hand side (two screws) of the server.

ÊReconnect all the cables you disconnected beforehand on the rear of the server.

ÊPress in the locking spring on both sides and push the server as far as it will go into the rack.

U41604-Z156-1-76

Options Guide

Page 73

Image 73

Fujitsu TX150 S3 manual Completion, V Caution

Contents

Options Guide PRIMERGY TX150 S3 Server SystemCopyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Introduction Procedure Safety notes Preparation Main memory ContinuedAccessible drives Controller in the PCI slots RemoteView components External SCSI interface Conversion standard PS to hot-plug PSPage Appendix Abbreviations, Related publications and Index Converting from the floorstand model to the rack model CompletionPage RemoteView Service Board S2 LP ContentsInstalling the external SCSI interface PCI slot assemblingContents 1.1 Overview of the documentation 1 IntroductionConcept and target groups Additional documentation about the serverExtensions and conversions 1.2 Extensions and conversionsReklamat-PC-LOG@fujitsu-siemens.com Further sources of informationIntroduction Additional accessible drivesHard disks extension box Additional controllers in the PCI slots1.3 Notational conventions Conversion standard power supply to hot-plug power supplyNotational conventions Conversion of the floorstand model to a rack modelV CAUTION 2 ProcedurePage Before operating the device V CAUTION 3 Safety notesV CAUTION Installation and operation V CAUTION Safety notesV CAUTION V CAUTION Safety notesSafety notes Batteries V CAUTIONNever remove parts of the CD-/DVD-ROM drive assembly Safety notes Notes on handling CDs and CD-/DVD-ROM drives V CAUTIONNote about the laser V CAUTIONSafety notes Modules with electrostatic-sensitive componentsFigure 1 ESD label 4.1 Floorstand model 4 Preparation4.1.1 Opening the server V CAUTIONFloorstand model 4.1.2 Removing the front coverPreparation 4.1.3 Removing the hard disk cover4.2.1 Opening the server 4.2 Rack modelRack model Preparation Rack modelFigure 7 Loosening the locking spring Figure 8 Removing the server from the rack cabinetV CAUTION Rack modelPreparation Figure 9 Loosening the screwsPreparation 4.2.2 Removing the rack front coverRack model Page 5.1 Equipping rules 5 Main memoryV CAUTION Extending/replacing the main memory 5.2 Extending/replacing the main memoryExtending/replacing the main memory Main memoryPage 6.1 Installing an accessible 5.25-inch drive 6 Accessible drivesV CAUTION Accessible drives Installing an accessible 5.25-inch driveV CAUTION Figure 16 Attaching the EasyClick rails - DVD-ROM burnerInstalling an accessible 5.25-inch drive Accessible drivesAccessible drives Installing an accessible 5.25-inch driveFigure 19 Attaching the EasyClick rails - magnetic tape drive VXA-2 Accessible drives 6.2 Installing the hard disks extension boxInstalling the hard disks extension box V CAUTIONAccessible drives Installing the hard disks extension boxV CAUTION 7 Controller in the PCI slotsPCIe Slot PCI Slot PCI Slot PCI Slot PCI Slot PCI Slot Installing a controller 7.1 Installing a controllerV CAUTION Controller in the PCI slotsInstalling a controller Controller in the PCI slotsPCI slot assembling 7.2 PCI slot assemblingController in the PCI slots 8 RemoteView components 8.1 RemoteView Service Board S2 LPV CAUTION Figure 25 Connecting cables to the RSB S2 LP RemoteView Service Board S2 LPFigure 26 Connecting cables to the system board RemoteView componentsRemoteView Service Board S2 LP RSB S2 LPFigure 27 Connecting external cables RemoteView componentsRemoteView Service Board S2 LP 9 External SCSI interface 9.1 Installing the external SCSI interfaceV CAUTION Page V CAUTION 10 Conversion standard PS to hot- plug PSV CAUTION Conversion standard PS to hot-plug PS Figure 30 Taking out the standard power supplyFigure 29 Loosening the screws Ê Fasten the Power backplane with one knurled screw see the circle Ê Insert the Power backplane in the PS cageFigure 31 Installing the Power backplane in the PS cage Conversion standard PS to hot-plug PSConversion standard PS to hot-plug PS Figure 32 Installing the PS cageV CAUTION Conversion standard PS to hot-plug PS Figure 33 Fastening the PS cage in the housingOptions Guide U41604-Z156-1-76Figure 34 Fastening the PS cage at the rear side Conversion standard PS to hot-plug PSConversion standard PS to hot-plug PS Conversion standard PS to hot-plug PS Figure 36 Locking the power supply moduleV CAUTION Conversion standard PS to hot-plug PSConversion standard PS to hot-plug PS Mounting the anti-tilt bracket only floorstand modelFigure 38 Mounting the anti-tilt bracket V CAUTION Conversion standard PS to hot-plug PSPage V CAUTION 11 Converting from the floorstand model to the rack modelFigure 41 Removing the screws Converting from the floorstand model to the rack modelFigure 42 Removing the right-hand side cover V CAUTION Converting from the floorstand model to the rack modelConverting from the floorstand model to the rack model Figure 44 Installing the operating panel moduleU41604-Z156-1-76 Converting from the floorstand model to the rack modelPage 12.1 Floorstand model 12 Completion12.1.1 Attaching the hard disk cover V CAUTIONFloorstand model 12.1.2 Attaching the front coverCompletion Completion 12.1.3 Closing the server12.2.1 Attaching the rack front cover 12.2 Rack modelRack model Completion Ê Attach the rack front cover using two screws on each sideRack model Ê Attach the rack front cover from the frontRack model 12.2.2 Closing the serverCompletion Figure 51 Attaching the top coverV CAUTION CompletionCompletion Rack modelFigure 53 Fastening the server in the rack cabinet 13.1 Cabling 13 Appendix13.1.1 SCSI version 1-channel SCSI version with onboard SCSI controllerSCSI PowerIDE/FD DataPower CablingSCSI IDE/FDCabling Power SCSIIDE/FD Data Cable prefix T26139 Figure 56 Cabling hard disk extension boxPower 1.132 SATA versionCabling Options GuidePage Abbreviations BIOSANSI ASR&REEPROM AbbreviationsIOOP Abbreviations HDDPOST NVRAMRAID RTDSSCSI Abbreviations SCASDDC SDRAMPage 12 System Board D1979 Technical Manual 13 BIOS-Setup Reference Manual 1 Safety 2 Warranty 3 PRIMECENTER Rack Technical ManualRelated publications 4 DataCenter Rack Technical Manual 5 19 inch rack Technical ManualRelated Publications 15 Global Array Manager Client Software User’s Guide 16 Configurator14 Integrated Mirroring User’s Guide Index Page Fujitsu Siemens Computers GmbH User Documentation 81730 München Comments Suggestions CorrectionsGermany Submitted by Comments on PRIMERGY TX150 S3 Server SystemPage Fujitsu Siemens Computers GmbH User Documentation 81730 München Comments Suggestions CorrectionsGermany Submitted by Comments on PRIMERGY TX150 S3 Server SystemPage Hinweise zum vorliegenden Dokument Information on this documenthttp//ts.fujitsu.com