Manuals / Fujitsu / Computer Equipment / Server

Fujitsu TX150 S3 manual Preparation, Floorstand model, Opening the server, V Caution

Models: TX150 S3

1 95

Download 95 pages 1.83 Kb

Page 21

Image 21

4 Preparation

VCAUTION!

Observe the safety instructions in the chapter “Safety notes” on page 7 et seqq. .

4.1Floorstand model

4.1.1Opening the server

ÊTerminate all applications and shut down the server correctly.

ÊIf your operating system has not switched off the sever, press the on/off switch.

ÊPull all power connectors out of the power outlets.

ÊIf required, remove the lock on the side cover.

Figure 2: Loosening the screws

ÊUnlock the server (1).

ÊLoosen the two screws at the rear side (2).

ÊPush back the left-hand side cover approxiate 2 cm (3).

ÊRemove the left-hand side cover (4).

U41604-Z156-1-76

Options Guide

Page 21

Image 21

Fujitsu TX150 S3 manual Preparation, Floorstand model, Opening the server, V Caution

Contents

Options Guide PRIMERGY TX150 S3 Server SystemComments… Suggestions… Corrections… Copyright and TrademarksCertified documentation according to DIN EN ISO Introduction Procedure Safety notes Preparation Main memory ContinuedAccessible drives Controller in the PCI slots RemoteView components External SCSI interface Conversion standard PS to hot-plug PSPage Appendix Abbreviations, Related publications and Index Converting from the floorstand model to the rack model CompletionPage RemoteView Service Board S2 LP ContentsInstalling the external SCSI interface PCI slot assemblingContents 1.1 Overview of the documentation 1 IntroductionConcept and target groups Additional documentation about the serverExtensions and conversions 1.2 Extensions and conversionsReklamat-PC-LOG@fujitsu-siemens.com Further sources of informationIntroduction Additional accessible drivesHard disks extension box Additional controllers in the PCI slots1.3 Notational conventions Conversion standard power supply to hot-plug power supplyNotational conventions Conversion of the floorstand model to a rack modelV CAUTION 2 ProcedurePage 3 Safety notes Before operating the device V CAUTIONV CAUTION Safety notes Installation and operation V CAUTIONV CAUTION V CAUTION Safety notesSafety notes Batteries V CAUTIONNever remove parts of the CD-/DVD-ROM drive assembly Safety notes Notes on handling CDs and CD-/DVD-ROM drives V CAUTIONNote about the laser V CAUTIONModules with electrostatic-sensitive components Safety notesFigure 1 ESD label 4.1 Floorstand model 4 Preparation4.1.1 Opening the server V CAUTIONFloorstand model 4.1.2 Removing the front coverPreparation 4.1.3 Removing the hard disk cover4.2 Rack model 4.2.1 Opening the serverRack model Preparation Rack modelFigure 7 Loosening the locking spring Figure 8 Removing the server from the rack cabinetV CAUTION Rack modelPreparation Figure 9 Loosening the screws4.2.2 Removing the rack front cover PreparationRack model Page 5 Main memory 5.1 Equipping rulesV CAUTION Extending/replacing the main memory 5.2 Extending/replacing the main memoryExtending/replacing the main memory Main memoryPage 6 Accessible drives 6.1 Installing an accessible 5.25-inch driveV CAUTION Accessible drives Installing an accessible 5.25-inch driveV CAUTION Figure 16 Attaching the EasyClick rails - DVD-ROM burnerInstalling an accessible 5.25-inch drive Accessible drivesInstalling an accessible 5.25-inch drive Accessible drivesFigure 19 Attaching the EasyClick rails - magnetic tape drive VXA-2 Accessible drives 6.2 Installing the hard disks extension boxInstalling the hard disks extension box V CAUTIONAccessible drives Installing the hard disks extension box7 Controller in the PCI slots V CAUTIONPCIe Slot PCI Slot PCI Slot PCI Slot PCI Slot PCI Slot Installing a controller 7.1 Installing a controllerV CAUTION Controller in the PCI slotsInstalling a controller Controller in the PCI slots7.2 PCI slot assembling PCI slot assemblingController in the PCI slots 8.1 RemoteView Service Board S2 LP 8 RemoteView componentsV CAUTION Figure 25 Connecting cables to the RSB S2 LP RemoteView Service Board S2 LPFigure 26 Connecting cables to the system board RemoteView componentsRemoteView Service Board S2 LP RSB S2 LPFigure 27 Connecting external cables RemoteView componentsRemoteView Service Board S2 LP 9.1 Installing the external SCSI interface 9 External SCSI interfaceV CAUTION Page 10 Conversion standard PS to hot- plug PS V CAUTIONV CAUTION Figure 30 Taking out the standard power supply Conversion standard PS to hot-plug PSFigure 29 Loosening the screws Ê Fasten the Power backplane with one knurled screw see the circle Ê Insert the Power backplane in the PS cageFigure 31 Installing the Power backplane in the PS cage Conversion standard PS to hot-plug PSFigure 32 Installing the PS cage Conversion standard PS to hot-plug PSV CAUTION Conversion standard PS to hot-plug PS Figure 33 Fastening the PS cage in the housingOptions Guide U41604-Z156-1-76Figure 34 Fastening the PS cage at the rear side Conversion standard PS to hot-plug PSConversion standard PS to hot-plug PS Conversion standard PS to hot-plug PS Figure 36 Locking the power supply moduleV CAUTION Conversion standard PS to hot-plug PSMounting the anti-tilt bracket only floorstand model Conversion standard PS to hot-plug PSFigure 38 Mounting the anti-tilt bracket V CAUTION Conversion standard PS to hot-plug PSPage V CAUTION 11 Converting from the floorstand model to the rack modelConverting from the floorstand model to the rack model Figure 41 Removing the screwsFigure 42 Removing the right-hand side cover V CAUTION Converting from the floorstand model to the rack modelConverting from the floorstand model to the rack model Figure 44 Installing the operating panel moduleU41604-Z156-1-76 Converting from the floorstand model to the rack modelPage 12.1 Floorstand model 12 Completion12.1.1 Attaching the hard disk cover V CAUTION12.1.2 Attaching the front cover Floorstand modelCompletion Completion 12.1.3 Closing the server12.2 Rack model 12.2.1 Attaching the rack front coverRack model Completion Ê Attach the rack front cover using two screws on each sideRack model Ê Attach the rack front cover from the frontRack model 12.2.2 Closing the serverCompletion Figure 51 Attaching the top coverV CAUTION CompletionRack model CompletionFigure 53 Fastening the server in the rack cabinet 13.1 Cabling 13 Appendix13.1.1 SCSI version 1-channel SCSI version with onboard SCSI controllerSCSI PowerIDE/FD DataPower CablingSCSI IDE/FDCabling Power SCSIIDE/FD Data Cable prefix T26139 Figure 56 Cabling hard disk extension boxPower 1.132 SATA versionCabling Options GuidePage Abbreviations BIOSANSI ASR&REEPROM AbbreviationsIOOP Abbreviations HDDPOST NVRAMRAID RTDSSCSI Abbreviations SCASDDC SDRAMPage 12 System Board D1979 Technical Manual 13 BIOS-Setup Reference Manual 1 Safety 2 Warranty 3 PRIMECENTER Rack Technical ManualRelated publications 4 DataCenter Rack Technical Manual 5 19 inch rack Technical Manual15 Global Array Manager Client Software User’s Guide 16 Configurator Related Publications14 Integrated Mirroring User’s Guide Index Page Fujitsu Siemens Computers GmbH User Documentation 81730 München Comments Suggestions CorrectionsGermany Submitted by Comments on PRIMERGY TX150 S3 Server SystemPage Fujitsu Siemens Computers GmbH User Documentation 81730 München Comments Suggestions CorrectionsGermany Submitted by Comments on PRIMERGY TX150 S3 Server SystemPage Information on this document Hinweise zum vorliegenden Dokumenthttp//ts.fujitsu.com