J56 | Furuno SC-120 specs

2.INSTALLATION

9.Fix the PH connector assy. with a clampJ8J107(BLK)as shown in the illustration below.

		9	(RED)	J1	J3
Pass PH connector	J2	J56	(BLK)20P8171			20P8164
through clamp		J4(RED)
through clamp
DGPS Receiver					J4	J1
Assy.

Processor unit, cover removed, top view

10.Close the top cover of the processor unit.

11.Mount the DGPS antenna and whip antenna, referring to section 2.2.

2-24

Image 38

Furuno SC-120 manual J56

Contents

Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting Iii Word to the Owner of the SC-120 FeaturesForeword System Configuration System configuration Equipment List Name Type Code No Qty Remarks Software Version List Vii This page is intentionally left blank Specifications of Satellite Compass SC-120 Power Supply Principle of Operation Principle of satellite compass operation This page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Display unit, processor unit Example of improper installationExample of improper installation Installing the Antenna Units Installation post Fastening antenna unit to a post Coating bolt, nut and washer with silicone rubber Antenna element Dgps antenna unit Mounting the Dgps antenna Antenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Desktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methods Name Type Flush mountingFlush mount F Flush mount S Antenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFB Confirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menu Choosing heading source Adjusting antenna orientationHeading setup menu Heading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top view Installing the Dgps Beacon Receiver Kit Connection of External Equipment Procedure Processor unit, cover removed, top view J56 Display unit OperationControls Press the DIM key Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data display ROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run display Alarm menu AlarmsMain menu 2. Choose Alarms and press the ENT key Alarm menu, GPS buzzer options Satellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Output Data Heading NAV OUT menu Navigation dataInterface Format selection window Log pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection window Geodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Manual Dgps setup Dgps SetupDemonstration mode Dgps menu INT Beacon receiver selection window Station User display Programming user beacon stationsBeacon station display Display for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others Menu Others menu Trip Menu Resetting Distance RunReset Distance prompt Trip menu This page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1 MAINTENANCE, Troubleshooting Diagnostic test sequence Diagnostic test2 TEST2 display Program version no. display Program NumberClearing Data Prompts for erasure of data Battery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging battery Error Message Meaning Remedy Replacement of FuseError Messages Message display Error messages con’t from previous Batttery Appendix Menu Tree Geodetic Chart Codes North American Digital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rolling HDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output Ports Parts Location Processor unit, cover removed Parts List R U N O ＰａｃｋｉｎｇＬｉｓｔ SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1