Manuals / Garmin / Computer Equipment / Power Supply

Garmin EDP70 Reserve Input, Ground, Primary Input, Output, External Batteries E.P.O, Inhibited

Models: EDP70

1 67

Download 67 pages 37.68 Kb

Page 35

Image 35

Computer relay

interface - FEMALE

FRONT

RAU - FEMALE

RS232 - MALE

Modem and	REAR
Multicom	REAR
power supplies
	Label

			sec. max 14 AWG
U1V1W1N PE U V W N U2V2W2 N
RESERVE INPUT	GROUND	PRIMARY INPUT	OUTPUT	EXTERNAL BATTERIES E.P.O.	BatteryCharger	Inhibited

Figure 20 - 24 – 12/18/24kVA: Cable Connections

MI00/10056 rev. 8 — 05/2006-- page 35

Page 35

Image 35

Garmin EDP70 manual Reserve Input, Ground, Primary Input, Output, External Batteries E.P.O, BatteryCharger, Inhibited

Contents

USER HANDBOOK UNINTERRUPTIBLE POWER SYSTEM 24/36/50/80kVA3 phase input / 3 phase output EDP70 PLUS1 SAVE THESE INSTRUCTIONS INJURIES CAUSED BY CONTACT WITH CORROSIVE LIQUIDS ELECTRICAL PRECAUTIONSEMERGENCY PROCEDURE ELECTRIC SHOCKContents 13.0 BATTERIES 14.0 MAINTENANCE AND SPARE PARTS12.0 REMOTE ALARMS 11.0 COMPUTER INTERFACEFigures Handling EQUIPMENT DELIVERY AND STORAGEDelivery Unpackingpage 8 -- MI00/10056 rev. 8 -05/2006 1.2 Summary of the equipment 1.0 INTRODUCTION1.1 Summary of the manual AC UTILITY INPUT WITH THE JUMPER 24kVA - STANDARD CONFIGURATION36kVA - STANDARD CONFIGURATION 36kVA - 480V/208V CONFIGURATIONRECTIFIER/INVERTER page 12 -- MI00/10056 rev. 8 -05/2006 24/36kVA Ratings50/80kVA Ratings Transfer onto the reserve line is caused by two conditions DIRECT CURRENT SUPPLY ALTERNATING CURRENT SUPPLY 2.0 SAFETY2.5 Battery safety equipment 2.3 Electrical precautions2.4 Battery precautions 4.1 Mechanical characteristics 4.0 INSTALLATION3.0 STORAGE 23.62 30,01.18 645,025.397.87 600,0page 18 -- MI00/10056 rev. 8 -05/2006 ALL MEASUREMENTS ARE IN MILLIMETERS AND INCHESALL MEASUREMENTS ARE IN MILLIMETERS AND INCHES page 20 -- MI00/10056 rev. 8 -05/2006 Figure 10 - “A” Battery Cabinet Drawing for 24/36kVA RatingsMI00/10056 rev. 8 - 05/2006-- page Figure 11 - “B” Battery Cabinet Drawing for 24/36kVA Ratingspage 22 -- MI00/10056 rev. 8 -05/2006 Figure 12 - “E” Battery Cabinet Drawing for 50/80kVA RatingsMI00/10056 rev. 8 - 05/2006-- page Figure 13 - “F” Battery Cabinet Drawing for 50/80kVA RatingsConnection FUSE Figure 15 - “D” Battery Cabinet Drawing for 50/80kVA RatingsConnection PointsEnsure the interconnecting cables do not cause a hazard to the user 5 Grounding conductors are sized per NEC Vin/Vout page 28 -- MI00/10056 rev. 8 -05/2006T r - T k 4.4 VentilationPd V = 2770 - - - - - - e 0.125 h Tk / T0 NO UNAUTHORIZED OPERATION 5.0 CONNECTIONUNINTERRUPTIBLE POWER SYSTEM be connected before the power input cables All power connection must carried out by qualifiedlicensed personnel experienced in wiring this type of equipment The safety ground wire must5.1 Electrical connections All electrical connections must be made by a qualified electricianand meet local electrical code standards S1 = Equipment ON/OFF Breaker S2 = Equipment Reserve SwitchS3 = Equipment By-pass Switch Battery CompartmentCable channel Output, Reserve, Input and External Battery TerminalsHinged panel security screws Cable supportPRIMARY INPUT BatteryChargerRESERVE INPUT GROUNDS1 = Equipment ON/OFF Breaker = Equipment By-pass switch= Equipment Reserve switch = Equipment OUTPUT BreakerFigure 22 - 36 - 24/30/36kVA Connections page 38 -- MI00/10056 rev. 8 - 4/2005 Modem andREAR = RESERVE OUTPUT switch page 40 -- MI00/10056 rev. 8 -05/2006 Figure 25 - 50/80kVA Connectionscontacts BatterychargeE.P.O inhibitedc Thermostick connector 50/80kVA only 5.4 Signal connections a Emergency Power Offb Battery charge inhibited The user controls are situated on the front panel, see Figure 6.0 CONTROLS6.2 Control Panel 7.0 START UP 8.0 MAINTENANCE BYPASS9.1 Installing the EPO 9.0 SHUT-DOWN10.3 Liquid Crystal Display 10.0 VISUAL AND AUDIBLE ALARMS10.1 Silencing Audible Alarm 10.2 Mimic10.4 Display Page Headings RECT/BATT ALARMS NO ALARMS ACTIVEINVERTER ALARMS NO ALARMS ACTIVE LOAD/RES ALARMS NO ALARMS ACTIVESELECTED LANGUAGE ENGLISH BATTERY TEST WEEKLYRECTIFIER Vdc xxx V Idc xxx A POWER HISTORY DOWN TO ACCESSBATTERY Vb xxx V Ib xxx A UPS xx kVA SYSTEM NORMALpress once LAST MAINS FAILURE xxd xxh xxm xxs INVERTER A xxx A B xxx A C xxx A Vdc xxx V Ib xxxx AINVERTER F xx.x Hz A xxx V B xxx V C xxx INVERTER F xx.x Hz AB xxx V BC xxx V CA xxxLOAD f xx.x Hz A xxx V B xxx V C xxx CONDITION MAIN PAGE HEADING ALARMS10.5 Abnormal operating mode messages MESSAGEBATTERY DISCHARGING AUT calc DIS xx min CONDITION RECTIFIER/BATTERY ALARMSMESSAGE NOT CALIBRATED CONDITION LOAD/RESERVE ALARMSMESSAGE 10.6 Power History Figure 28 Power History Structuresystem normal message 10.7 Battery Test10.8 Battery Autonomy Test 10.9 Resetting data loss manually11.1 AS400 11.0 COMPUTER INTERFACEFigure 29 EDP 70 Plus Computer Interface Pin Layout 11.2 RS232 12.0 REMOTE ALARMSFigure 30 EDP70 PLUS Remote Alarms Pin Layout 13.1 EDP70 PLUS/24/18/12 Battery Installation/Start-up 13.0 BATTERIES13.2 EDP70 PLUS/24/18/12 Optional Battery Cubicle Figure 31- EDP70 PLUS/24/18/12 Internal Battery Shelves13.4 EDP70 PLUS above 24KVA Battery Cubicle 14.0 MAINTENANCE AND SPARE PARTS13.3 EDP70 PLUS above 24KVA Battery Installation/Start-up Event EDP70 PLUS SYSTEM LOGDate Time

RESERVE INPUT

GROUND

PRIMARY INPUT

OUTPUT

EXTERNAL BATTERIES E.P.O.

BatteryCharger

Inhibited