Heater Assembly, Joining of Tube Sections | Gas-Fired Products 75

Form #43343530 July 08

Typical Assembly Overview

(PTS 40FT Shown)

Turbulator

(See specifications section 5 for required quantities.)

Typical

Overlap

Flue

Termina

8.2) HEATER ASSEMBLY

–15–

			U-Bolt Clamp &
			5/16" Hex Nuts
		4"OD x 10Ft. Tube
		See section 7
		for required tubes.
	Mounting Flange		8’ - 10’
	24 Hole for Aluminized Steel Tubes		8’ - 10’
	24 Hole for Aluminized Steel Tubes
Burner		6 Hole for Alumi-Therm Steel Tubes
Burner		8’ - 9’ ¼”
Box	Gasket	8’ - 9’ ¼”

Maximum 6” distance from burner box to the tube support/hanger bracket.

Wire Hanger

Tube Support Bracket

Tube Coupling

(Typical each tube joint.) 8’ - 10’

#10 Self-Drill Screws (Typical all tube supports, tube couplings and flue terminal.)

Not Less

Than 10”

/ JOINING OF TUBE SECTIONS

Burner Box

Suspension

Chain

5 hanging points to be used for suspension for a typical 40ft long system. There must be two hanging points on the first tube and one on each of the other tubes

Image 16

Gas-Fired Products N7/L7, 100, 40, 150, 175, 200 manual Heater Assembly, Joining of Tube Sections

Contents

Installation and Operation Instructions Table of Contents Safety Installer ResponsibilityInstallation Requirements General Information For Canada only High Altitude Minimum Clearances to Combustibles Minimum Clearances to Combustibles Specifications Packing List Burner Package Numbers Natural GAS PTU 40-200 Body Package Descriptions Reflector, 4’ 11 ½’ Accessories End Reflector Accessory Package Exhaust Hood Package Typical Layouts PTU / PTS Series Emitter Length Body Length Model Typical Assembly Layout Poisonous GAS and Soot Hazard PTS Series Dimensions PTU Series Heater Assembly Joining of Tube Sections Typical Assembly Overview PTU 40FT Shown Typical Suspension Methods Suspension Hazard Assembly of Tube Sections CUT Hazard Assembly of Extension Section MIN 8’ MAX 10’ Between Hangers Inserting Turbulators Adding Reflectors Ft. Turbulator Sections Adding Optional 90º Elbow PTS only Adding Optional Corner Reflector PTS only Adding 180U-Bend PTU only Adding Optional U-BEND Reflector PTU only Attaching Burner BOX Assembly Connecting the Tiss System Instructions End View Angle Mounted Heaters only GAS Connections and Regulations Do not USE AN Open Flame of ANY Kind to Test for Leaks KEY Dimensions and Components of the GAS Connections Supply Pressure Instructions for Pressure Test Gauge ConnectionManifold PRESSURE- Combination GAS Valve is Factory SET Electrical Connections GAS Control Valve Ignition Module Terminal Designations 24VAC/R TH/WPS/W GND LOW Voltage 24V Thermostat Connections Single Heater LOW Voltage 24V Thermostat Connections Multiple Heaters Venting Single Heater Venting Vertical Through the Roof Single Heater Venting Horizontal Through Sidewall #10 Self-Drill Vent Pipe Screws Common Vent Diameter Indirect Venting Unvented Heaters AIR for Combustion Direct Outside AIR for Combustion Lighting and Shutdown Instructions Side View Sequence of Operation Burner Component Locations Cleaning and Maintenance Electric Shock & Explosion Hazard Troubleshooting Guide 22.0 Form #43343530 JJuly Replace air switch Restart Troubleshooting Yes Replacing Parts Removal of Main Burner and Electrodes Removal of GAS Valve and Manifold Assembly AIR Switch Pressure Check Ignition System Checks Ignition Module DiagnosticsTo Check Flame Sensor Circuit Installation Data Replacement Parts Guide Burner BOX Labels/Manual 22c Body Components Description