NOT LESS THAN WIDTH OF RANGE

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT: Save these instructions for the local electrical inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Leave these instructions with the appliance after installation is completed.

NOTE TO CONSUMER: Keep this Use and Care Guide and Installation Instructions for future use.

NOTE: This appliance must be properly grounded.

TOOLS YOU WILL NEED

Large blade screwdriver

Channel lock pliers or small ratchet wrench with 3/16-inch socket (for leveling range)

1/4-inch hex head nutdriver

ELECTRICAL REQUIREMENTS

CAUTION, FOR PERSONAL SAFETY:

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or time delay fuse, as noted on the rating plate.

Wiring must conform to National Electric Codes.

If the electric service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.

Because range terminals are not accessible after the range is in position, flexible service conduit or cord must be used.

STEP 1

PREPARE THE OPENING

112 inch spacing is recommended from the range to adjacent vertical walls above cooktop surface.

Allow 30 inches minimum clearance between surface units and bottom of unprotected wood or metal top cabinet, and 15 inches minimum between countertop and adjacent cabinet bottom.

EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installation instructions packed with that appliance.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a min. of 5 inches beyond the bottom of the cabinets. Make sure the wall coverings, countertops and cabinets around the range, oven or cooktop can withstand heat generated by the range up to 200°F.

 

 

 

 

 

 

 

HOOD

 

 

 

 

 

 

 

 

5MIN.

30

 

 

 

 

 

 

 

 

MIN. 15

 

 

 

 

 

 

 

 

MIN.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LOCATE

 

 

 

 

 

 

 

 

OUTLET BOX

WALL

 

 

 

 

 

 

WITHIN EITHER

 

 

 

 

 

 

 

SHADED AREA

 

1

1

2

 

 

 

 

 

 

 

 

 

 

 

 

 

MIN.

 

 

 

 

 

INSTALL

 

 

 

 

 

 

 

 

OUTLET BOX

 

 

 

 

 

 

 

ON EITHER

WALL

C OF RANGE

 

 

 

SIDE OF C

 

 

 

L

 

 

 

 

L

 

 

7

1 2

 

 

 

 

 

 

 

 

 

 

 

OUTLET

7

7

1 2

1458

 

 

 

 

BOX

 

 

3

1

2

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

1 4

 

 

 

 

 

 

 

CORD FLOOR

Anti-Tip Bracket (install in either rear corner)

(continued next page)

35

Page 35
Image 35
GE 10-95 CG warranty Installation Instructions, Before YOU Begin

10-95 CG specifications

The GE 10-95 CG is a notable locomotive designed to meet the demands of freight transport with efficiency and reliability. Built by General Electric, this model showcases a combination of advanced technology and impressive engineering, making it a prominent choice in the rail industry.

One of the primary features of the GE 10-95 CG is its powerful diesel engine. The locomotive is equipped with a 12-cylinder 7FDL engine, capable of producing substantial horsepower that allows it to handle heavy loads across challenging terrains. This engine configuration not only provides reliability but also ensures operational efficiency, allowing for lower fuel consumption over longer distances.

The 10-95 CG is recognized for its distinct, rugged design that is built to withstand diverse environmental conditions. Its robust frame and sturdy body contribute to its longevity and durability, while the optimized aerodynamics reduce drag, enhancing fuel efficiency. The locomotive's structure is designed for easy access and maintenance, allowing operators to keep it in optimal working condition with minimal downtime.

In terms of technologies, the GE 10-95 CG integrates advanced electronic systems that enhance performance and monitoring. The locomotive features a sophisticated microprocessor-based control system that enables precise engine management, ensuring optimal operation under varying conditions. Additionally, the use of dynamic braking technology provides enhanced control, reducing wear and tear on the braking system while improving safety.

The traction system of the GE 10-95 CG employs alternating current (AC) traction motors, which are known for their efficiency and reduced maintenance requirements compared to traditional DC motors. This technology results in better acceleration and overall performance, making the locomotive adept in both hauling heavy freight and navigating tight curves.

Another notable characteristic of the GE 10-95 CG is its ability to operate in multiple unit configurations. This allows for seamless coupling with other locomotives, enabling operators to scale their freight capacity as needed. The versatility of this locomotive makes it a valuable asset in various rail operations.

In summary, the GE 10-95 CG embodies a blend of power, efficiency, and advanced technology. With features designed for durability, operational efficiency, and ease of maintenance, it stands out as a formidable choice for freight transportation in the rail industry. Its innovative systems and robust performance characteristics ensure that it remains a reliable solution for meeting the demands of modern logistics and transportation.