HOME CANNING TIPS

Canning should be done on the cooktop only.

Pots that extend beyond 1 inch of the surface unit circle are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to the cooktop surfaces surrounding the surface units.

HOWEVER, DO NOT USE LARGE DIAMETER CANNERS OR OTHER LARGE DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures—and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm the glass cooktop surfaces.

Observe the Following Points in Canning

1.Be sure the canner fits over the center of the surface unit. If your cooktop or its location does not allow the canner to be centered on the surface unit, use smaller diameter pots for good canning results.

2.Flat-bottomed canners must be used. Do not use canners with flanged or rippled bottoms (often found in enamelware) because they don’t make enough contact with the surface units and take too long to boil water.

RIGHT WRONG

Flat-bottomed canners are required for glass cooktops.

3.When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball and Kerr; and the United States Department of Agriculture Extension Service.

4.Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.

NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed. The process time will be shortened by:

(1)using a pressure canner, and

(2)starting with HOT tap water for fastest heating of large quantities of water.

CAUTION:

Safe canning requires that harmful microorganisms are destroyed and that the jars are sealed completely. When canning foods in a water-bath canner, a gentle but steady boil must be maintained for the required time. When canning foods in a pressure canner, the pressure must be maintained for the required time.

After you have adjusted the controls, it is very important to make sure the prescribed boil or pressure levels are maintained for the required time.

The cooktop surface units have temperature limiters that prevent the glass cooktop from getting too hot. If the bottom of your canner is not flat, the surface unit can overheat, triggering the temperature limiters to cycle the unit off for a time. This will stop the boil or reduce the pressure in the canner.

Since you must make sure to process the canning jars for the prescribed time, with no interruption in processing time, you cannot can on any of the cooktop surface units if your canner is not flat enough.

What is a Temperature Limiter?

Every radiant surface unit has a Temperature Limiter. The Temperature Limiter protects the glass cooktop from getting too hot.

The Temperature Limiter may cycle the units off for a time if:

The pan boils dry.

The pan bottom is not flat.

The pan is off center.

There is no pan on the unit.

14

Page 14
Image 14
GE 10-95 CG warranty Home Canning Tips, Observe the Following Points in Canning, Canning should be done on the cooktop only

10-95 CG specifications

The GE 10-95 CG is a notable locomotive designed to meet the demands of freight transport with efficiency and reliability. Built by General Electric, this model showcases a combination of advanced technology and impressive engineering, making it a prominent choice in the rail industry.

One of the primary features of the GE 10-95 CG is its powerful diesel engine. The locomotive is equipped with a 12-cylinder 7FDL engine, capable of producing substantial horsepower that allows it to handle heavy loads across challenging terrains. This engine configuration not only provides reliability but also ensures operational efficiency, allowing for lower fuel consumption over longer distances.

The 10-95 CG is recognized for its distinct, rugged design that is built to withstand diverse environmental conditions. Its robust frame and sturdy body contribute to its longevity and durability, while the optimized aerodynamics reduce drag, enhancing fuel efficiency. The locomotive's structure is designed for easy access and maintenance, allowing operators to keep it in optimal working condition with minimal downtime.

In terms of technologies, the GE 10-95 CG integrates advanced electronic systems that enhance performance and monitoring. The locomotive features a sophisticated microprocessor-based control system that enables precise engine management, ensuring optimal operation under varying conditions. Additionally, the use of dynamic braking technology provides enhanced control, reducing wear and tear on the braking system while improving safety.

The traction system of the GE 10-95 CG employs alternating current (AC) traction motors, which are known for their efficiency and reduced maintenance requirements compared to traditional DC motors. This technology results in better acceleration and overall performance, making the locomotive adept in both hauling heavy freight and navigating tight curves.

Another notable characteristic of the GE 10-95 CG is its ability to operate in multiple unit configurations. This allows for seamless coupling with other locomotives, enabling operators to scale their freight capacity as needed. The versatility of this locomotive makes it a valuable asset in various rail operations.

In summary, the GE 10-95 CG embodies a blend of power, efficiency, and advanced technology. With features designed for durability, operational efficiency, and ease of maintenance, it stands out as a formidable choice for freight transportation in the rail industry. Its innovative systems and robust performance characteristics ensure that it remains a reliable solution for meeting the demands of modern logistics and transportation.