Installation Instructions

INSTALL THE COOKTOP

10PREPARE THE COOKTOP (cont.)

Remove the blank 9-pin connector plug from the

9-pin receptacle on the bottom of the cooktop and discard. Connect the 9-pin plug on the blower assembly to the matching 9-pin receptacle on the bottom of the cooktop. Secure the connector cover to the cooktop using 3 screws, making sure the power cord comes out the U-shaped opening with the wires to the motor.

9-pin

 

connectors

Connector

 

 

cover

11INSTALL THE PRESSURE REGULATOR AND CONNECT

Regulator

Solid piping or flexible connector

Union

Solid piping

or flexible connector

Shut-off valve

Pipe stub

Using pipe sealant, approved by local codes, install the supplied pressure regulator in the gas line as close to the cooktop inlet as possible. Allowances for ventilation ducting may be necessary.

Do not route the gas line under the access box under the cooktop. Allow room for removal of the connector panel for servicing.

Make sure the regulator is installed in the proper direction.

Install a manual shut-off valve in the gas line in an easily accessible location.

11INSTALL THE PRESSURE

REGULATOR AND CONNECT

(cont.)

NOTE: Instead of using solid piping to connect to the pressure regulator, an approved flexible metal appliance connector may be used between the shut-off valve and the pressure regulator, if local codes permit.

Appropriate flare nuts and adapters are required at each end of the flexible connector.

Make sure all the knobs are in the off position. Hook up the gas line and check for leaks.

TEST FOR LEAKS

WARNING: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS! Do not use the cooktop until all connections have been leak tested.

Perform leak test per the following instructions:

1.Purchase a liquid leak detector or prepare a soap solution of one part water, one part liquid detergent.

2.When all connections have been made, make sure all cooktop controls are turned to OFF and turn the gas supply valve to ON.

3.Apply the liquid leak detector or the soap solution around all connections from the shut-off valve to the cooktop.

4.A leak is identified by a flow of bubbles from the area of the leak.

5.If a leak is detected, turn the gas supply off. Tighten the fitting. Turn the gas on and test again.

1.If the leak persists, turn the gas supply off and contact your dealer for assistance. Do not attempt to operate the cooktop if a leak is present.

IMPORTANT: Disconnect the cooktop and the individual shut-off valve from the gas supply piping system during any pressure testing of that system at test pressures greater than 1/2 psig. Isolate the cooktop from the gas supply piping system by closing the individual manual shut-off valve to the cooktop during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.

27

Page 27
Image 27
GE JGP990 Install the Pressure Regulator and Connect, Test for Leaks, Perform leak test per the following instructions

JGP990 specifications

The GE JGP990 is a high-performance gas range that stands out for its innovative features, robust construction, and impressive cooking capabilities. As part of General Electric's profile line, the JGP990 reflects the brand's legacy of quality and reliability while incorporating modern technologies that cater to the needs of today's home cooks.

At the forefront of the JGP990's features is its five-burner cooking surface, which includes a powerful 21,000 BTU tri-ring burner. This burner allows for versatile cooking techniques, from rapid boiling to gentle simmering. With multiple burner sizes, users can easily adjust the heat to accommodate various pot sizes and cooking methods. Furthermore, the continuous grates provide a seamless surface that allows for easy movement of pots and pans across the burners, enhancing convenience and efficiency.

In addition to its impressive burner options, the GE JGP990 is equipped with a built-in electric ignition system, providing reliable and easy start-up. This system eliminates the need for matches or lighters, allowing for a hassle-free cooking experience. The range also features heavy-duty cast iron grates that are not only durable but also add an element of professional-grade quality to the kitchen.

One of the standout features of the GE JGP990 is its integrated oven, which utilizes a powerful convection cooking system. This technology ensures even heat distribution, resulting in perfectly cooked meals, whether baking or roasting. The oven's self-cleaning mode simplifies maintenance, allowing users to spend less time scrubbing and more time enjoying their culinary creations.

The design of the JGP990 is equally impressive, available in stylish finishes that fit seamlessly into contemporary kitchens. The sleek stainless steel exterior not only enhances the aesthetic appeal but is also easy to clean, making it perfect for busy households.

Safety is paramount in the design of the GE JGP990, which includes features such as control lock and automatic shut-off. These elements provide peace of mind, especially for families with children.

Overall, the GE JGP990 gas range is a harmonious blend of power, versatility, and style, making it an ideal choice for both amateur cooks and professional chefs alike. Its cutting-edge features, reliable performance, and thoughtful design position it as a standout appliance in the ever-evolving culinary landscape.