Grounding Instructions

IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING

Advantium Oven

WARNING!

Improper use of the grounding plug can result in a risk of electric shock.

Ensure proper ground exists before use.

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

Do not under any circumstances cut or remove the ground prong from the power cord.

Do not use an adapter plug with this appliance.

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance.

For best operation, plug this appliance into its

The Vent Fan

This appliance is equipped with a power cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Consult a qualified electrician or service technician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

If the outlet is a standard 3-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 30 ampere, 4-prong wall outlet.

The fan will operate automatically under certain conditions (see Vent Fan section). Take care to prevent the starting and spreading of accidental cooking fires while the vent fan is in use.

nClean the underside of the Advantium often. Do not allow grease to build up on the Advantium or the fan filters.

nIn the event of a grease fire on the surface units below the Advantium, smother a flaming pan on the surface unit by covering the pan completely with a lid, a cookie sheet or a flat tray.

own electrical circuit to prevent flickering of lights, blowing of fuse or tripping of circuit breaker.

nUse care when cleaning the vent fan filters. Corrosive cleaning agents, such as lye- based oven cleaners, may damage the filters.

nWhen preparing flaming foods under the Advantium, turn the fan on.

nNever leave surface units beneath your Advantium unattended at high heat settings. Boilovers cause smoking and greasy spillovers that may ignite and spread if the Advantium vent fan is operating. To minimize automatic fan operation, use adequate sized cookware and use high heat on surface units only when necessary.

8

SAVE THESE INSTRUCTIONS

 

Page 8
Image 8
GE ZSA2201 owner manual Do not use an adapter plug with this appliance, For best operation, plug this appliance into its

ZSA2201 specifications

The GE ZSA2201 is a high-performance analog-to-digital converter that has garnered attention for its impressive features and capabilities, making it ideal for a variety of applications. This device is particularly sought after in industries such as telecommunications, instrumentation, and medical equipment, where precise data acquisition is critical.

One of the standout features of the GE ZSA2201 is its resolution, which can reach up to 24 bits. This high resolution allows the device to capture extremely subtle changes in voltage levels, providing users with the ability to measure signals with unparalleled accuracy. The converter's sampling rate is also noteworthy, supporting rates up to 1 MSPS (million samples per second). This enables the GE ZSA2201 to handle fast-changing signals, making it suitable for high-speed applications.

In terms of technologies, the ZSA2201 utilizes sophisticated delta-sigma modulation, which enhances its performance by reducing noise and improving the signal-to-noise ratio. This technology is essential for applications that require high fidelity in signal representation. The converter supports various input voltage ranges, making it versatile for different measurement scenarios. Users can easily configure it to suit their specific application needs, whether it be low-voltage or higher voltage environments.

The device is designed with integrated features that facilitate easy interfacing and communication. It supports standard digital communication protocols such as SPI (Serial Peripheral Interface), ensuring compatibility with a range of microcontrollers and other digital systems. This ease of integration simplifies the design process and reduces development time for engineers.

Moreover, the GE ZSA2201 is built to operate effectively across a wide temperature range, making it reliable in diverse environmental conditions. Its packaging is also designed to endure the rigors of industrial settings, ensuring robustness and longevity.

Finally, the GE ZSA2201 exemplifies a commitment to energy efficiency, with a low power consumption profile that contributes to longer operational life in battery-powered applications. In summary, the GE ZSA2201 is a versatile and high-performance analog-to-digital converter that excels in accuracy, speed, and reliability, making it a top choice for engineers looking to enhance their data acquisition systems.